DSPIC33FJ128MC804-E/ML Microchip Technology, DSPIC33FJ128MC804-E/ML Datasheet - Page 84

• Manufacturer Part Number: DSPIC33FJ128MC804-E/ML
• Description: IC, DSC, 16BIT, 128KB 40MHZ, 3.6V, QFN44
• Manufacturer: Microchip Technology
• Series: DsPIC33Fr

Specifications of DSPIC33FJ128MC804-E/ML

• Core Frequency: 40MHz
• Core Supply Voltage: 3.6V
• No. Of I/o's: 35
• Flash Memory Size: 128KB
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -40°C To +125°C
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 9x10b/12b, D/A 6x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 44-QFN
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

REGISTER 6-1:
DS70291D-page 84
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
Note 1: All of the Reset status bits can be set or cleared in software. Setting one of these bits in software does not
TRAPR
R/W-0
R/W-0
EXTR
2: If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
cause a device Reset.
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
CM: Configuration Mismatch Flag bit
1 = A configuration mismatch Reset has occurred
0 = A configuration mismatch Reset has NOT occurred
VREGS: Voltage Regulator Standby During Sleep bit
1 = Voltage regulator is active during Sleep
0 = Voltage regulator goes into Standby mode during Sleep
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
SLEEP: Wake-up from Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
IDLE: Wake-up from Idle Flag bit
1 = Device was in Idle mode
0 = Device was not in Idle mode
IOPUWR
R/W-0
R/W-0
SWR
Address Pointer caused a Reset
RCON: RESET CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
WDTO
R/W-0
U-0
Preliminary
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SLEEP
R/W-0
(2)
U-0
—
(1)
R/W-0
IDLE
U-0
—
© 2009 Microchip Technology Inc.
x = Bit is unknown
R/W-0
R/W-1
BOR
CM
VREGS
R/W-0
R/W-1
POR
bit 8
bit 0