DP83815DUJB National Semiconductor, DP83815DUJB Datasheet - Page 47
![IC, ENET CTRL 10BASET, 100MBPS, LBGA-160](/photos/19/0/190058/4551706_sml.jpg)
DP83815DUJB
Manufacturer Part Number
DP83815DUJB
Description
IC, ENET CTRL 10BASET, 100MBPS, LBGA-160
Manufacturer
National Semiconductor
Datasheet
1.DP83815DUJB.pdf
(108 pages)
Specifications of DP83815DUJB
Data Rate
100Mbps
Ethernet Type
10BASE-T
Supply Current
170mA
Supply Voltage Range
3V To 3.6V
Operating Temperature Range
0°C To +70°C
No. Of Pins
160
Termination Type
SMD
Filter Terminals
SMD
Rohs Compliant
No
Data Rate Max
100Mbps
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DP83815DUJB
Manufacturer:
NS
Quantity:
996
Company:
Part Number:
DP83815DUJB
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
DP83815DUJB
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
DP83815DUJB/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
4.0 Register Set
4.2.7 Interrupt Mask Register
This register masks the interrupts that can be generated from the ISR. Writing a “1” to the bit enables the corresponding
interrupt. During a hardware reset, all mask bits are cleared. Setting a mask bit allows the corresponding bit in the ISR to
cause an interrupt. ISR bits are always set to 1, however, if the condition is present, regardless of the state of the
corresponding mask bit.
31-26
Bit
Bit
25
24
23
22
21
7
6
5
4
3
2
1
0
Bit Name
Bit Name
RXEARLY
TXRCMP
RXRCMP
RXDESC
TXDESC
RXORN
RXIDLE
RXERR
DPERR
RMABT
SSERR
RXOK
TXOK
Offset: 0014h
(Continued)
Tag: IMR
Tx Descriptor
This event is signaled after a transmit descriptor when the INTR bit in the CMDSTS field has been
updated.
Tx Packet OK
This event is signaled after the last transmit descriptor in a successful transmission attempt has been
updated with valid status.
Rx Overrun
Set when a receive data FIFO overrun condition occurs.
Rx Idle
This event is signaled when the receive state machine enters the idle state from a running state. This will
happen whenever the state machine encounters an "end-of-list" condition (NULL link field or a descriptor
with OWN set).
Rx Early Threshold
Indicates that the initial Rx Drain Threshold has been met by the incoming packet, and the transfer of the
number of bytes specified by the DRTH field in the RXCFG register has been completed by the receive
DMA engine. This interrupt condition will occur only once per packet.
Rx Packet Error
This event is signaled after the last receive descriptor in a failed packet reception has been updated with
valid status.
Rx Descriptor
This event is signaled after a receive descriptor with the INTR bit set in the CMDSTS field has been
updated.
Rx OK
Set by the receive state machine following the update of the last receive descriptor in a good packet.
unused
Transmit Reset Complete
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Receive Reset Complete
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Detected Parity Error
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Signaled System Error
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Received Master Abort
When this bit is 0, the corresponding bit in the ISR will not cause an interrupt.
Access: Read Write
Size: 32 bits
47
Description
Description
Hard Reset: 00000000h
Soft Reset: 00000000h
www.national.com