DP83815DUJB National Semiconductor, DP83815DUJB Datasheet - Page 19
![IC, ENET CTRL 10BASET, 100MBPS, LBGA-160](/photos/19/0/190058/4551706_sml.jpg)
DP83815DUJB
Manufacturer Part Number
DP83815DUJB
Description
IC, ENET CTRL 10BASET, 100MBPS, LBGA-160
Manufacturer
National Semiconductor
Datasheet
1.DP83815DUJB.pdf
(108 pages)
Specifications of DP83815DUJB
Data Rate
100Mbps
Ethernet Type
10BASE-T
Supply Current
170mA
Supply Voltage Range
3V To 3.6V
Operating Temperature Range
0°C To +70°C
No. Of Pins
160
Termination Type
SMD
Filter Terminals
SMD
Rohs Compliant
No
Data Rate Max
100Mbps
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DP83815DUJB
Manufacturer:
NS
Quantity:
996
Company:
Part Number:
DP83815DUJB
Manufacturer:
Texas Instruments
Quantity:
10 000
Part Number:
DP83815DUJB
Manufacturer:
NS/国半
Quantity:
20 000
Company:
Part Number:
DP83815DUJB/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Subject to change without notice.
3.0 Functional Description
register is set to a one. If configured for parallel detect
mode, and any condition other than a single good link
occurs, then the parallel detect fault bit will set to a one, bit
4 of the ANER register (98h).
3.4.4 Auto-Negotiation Restart
Once Auto-Negotiation has completed, it may be restarted
at any time by setting bit 9 (Restart Auto-Negotiation) of the
BMCR to one. If the mode configured by a successful Auto-
Negotiation loses a valid link, then the Auto-Negotiation
process will resume and attempt to determine the
configuration for the link. This function ensures that a valid
configuration
disconnected.
A renegotiation request from any entity, such as a
management agent, will cause the DP83815 to halt any
transmit
break_link_timer expires (~1500 ms). Consequently, the
Link Partner will go into link fail and normal Auto-
Negotiation resumes. The DP83815 will resume Auto-
Negotiation after the break_link_timer has expired by
issuing FLP (Fast Link Pulse) bursts.
3.4.5 Enabling Auto-Negotiation via Software
It is important to note that if the DP83815 has been
initialized upon power-up as a non-auto-negotiating device
(forced technology), and it is then required that Auto-
Negotiation or re-Auto-Negotiation be initiated via software,
bit 12 (Auto-Negotiation Enable) of the Basic Mode Control
Register must first be cleared and then set for any Auto-
Negotiation function to take effect.
3.4.6 Auto-Negotiation Complete Time
Parallel detection and Auto-Negotiation take approximately
2-3 seconds to complete. In addition, Auto-Negotiation with
next page should take approximately 2-3 seconds to
complete, depending on the number of next pages sent.
Refer to Clause 28 of the IEEE 802.3u standard for a full
description of the individual timers related to Auto-
Negotiation.
3.5 LED Interfaces
The DP83815 has parallel outputs to indicate the status of
Activity (Transmit or Receive), 100 Mb/s Link, and 10 Mb/s
Link.
The LEDACTN pin indicates the presence of transmit or
receive activity. The standard CMOS driver goes low when
RX or TX activity is detected in either 10 Mb/s or 100 Mb/s
operation.
data
is
and
maintained
link
pulse
if
the
(Continued)
activity
cable
until
becomes
the
19
The LED100N pin indicates a good link at 100 Mb/s data
rate. The standard CMOS driver goes low when this
occurs. In 100BASE-T mode, link is established as a result
of input receive amplitude compliant with TP-PMD
specifications which will result in internal generation of
signal detect. This signal will assert after the internal Signal
Detect has remained asserted for a minimum of 500 us.
The signal will de-assert immediately following the de-
assertion of the internal signal detect.
The LED10N pin indicates a good link at 10 Mb/s data rate.
The standard CMOS driver goes low when this occurs. 10
Mb/s Link is established as a result of the reception of at
least seven consecutive normal Link Pulses or the
reception of a valid 10BASE-T packet. This will cause the
assertion of this signal. the signal will de-assert in
accordance with the Link Loss Timer as specified in IEEE
802.3.
The DP83815 LED pins are capable of 6 mA. Connection
of these LED pins should ensure this is not overloaded.
Using 2 mA LED devices the connection for the LEDs
could be as shown in Figure 3-5.
Figure 3-5 LED Loading Example
Rev O
www.national.com
V
DD