LIS331HHTR STMicroelectronics, LIS331HHTR Datasheet - Page 25

• Manufacturer Part Number: LIS331HHTR
• Description: ACCELEROMETER SENSOR 3AXIS 16-LG
• Manufacturer: STMicroelectronics
• Series: MEMS, nanor

Specifications of LIS331HHTR

• Axis: X, Y, Z
• Acceleration Range: ±6g, 12g, 24g
• Sensitivity: 12mg/digit, 6mg/digit, 3mg/digit
• Voltage - Supply: 2.16 V ~ 3.6 V
• Output Type: Digital
• Bandwidth: 50Hz ~ 1kHz Selectable
• Interface: I²C, SPI
• Mounting Type: Surface Mount
• Package / Case: 16-LGA
• Package Type: LGA
• Operating Supply Voltage (min): 2.16V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 3mm
• Product Height (mm): 1mm
• Product Length (mm): 3mm
• Mounting: Surface Mount
• Pin Count: 16
• Sensing Axis: X, Y, Z
• Acceleration: 6 g, 12 g, 24 g
• Digital Output - Number Of Bits: 16 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.16 V
• Supply Current: 10 uA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Digital Output - Bus Interface: I2C, SPI
• Shutdown: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LIS331HH
7.2
Table 18.
Table 19.
CTRL_REG2 (21h)
Table 20.
Table 21.
BOOT bit is used to refresh the content of internal registers stored in the flash memory
block. At the device power up the content of the flash memory block is transferred to the
internal registers related to trimming functions to permit a good behavior of the device itself.
If for any reason the content of trimming registers was changed it is sufficient to use this bit
to restore correct values. When BOOT bit is set to ‘1’ the content of internal flash is copied
BOOT
HPM1, HPM0
FDS
HPen2
HPen1
HPCF1,
HPCF0
BOOT
PM2
1
1
DR1
0
0
1
1
Power mode and low-power output data rate configurations (continued)
Normal-mode output data rate configurations and low-pass cut-off
frequencies
CTRL_REG2 register
CTRL_REG2 description
HPM1
PM1
Reboot memory content. Default value: 0
(0: normal mode; 1: reboot memory content)
High pass filter mode selection. Default value: 00
(00: normal mode; Others: refer to
Filtered data selection. Default value: 0
(0: internal filter bypassed; 1: data from internal filter sent to output register)
High pass filter enabled for interrupt 2 source. Default value: 0
(0: filter bypassed; 1: filter enabled)
High pass filter enabled for interrupt 1 source. Default value: 0
(0: filter bypassed; 1: filter enabled)
High pass filter cut-off frequency configuration. Default value: 00
(00: HPc=8; 01: HPc=16; 10: HPc=32; 11: HPc=64)
0
1
DR0
0
1
0
1
HPM0
PM0
1
0
Doc ID 16366 Rev 1
Output Data Rate [Hz]
FDS
Power mode selection
ODR
1000
100
400
50
Low-power
Low-power
Table 22
HPen2
)
HPen1
Low-pass filter cut-off
Output data rate [Hz]
frequency [Hz]
Register description
HPCF1
ODR
292
780
37
74
10
5
LP
HPCF0
25/37