734185-1 Tyco Electronics, 734185-1 Datasheet

Crimping, Stripping, Cutting Tools & Drills STRIP TOOL

734185-1

Manufacturer Part Number

734185-1

Description

Crimping, Stripping, Cutting Tools & Drills STRIP TOOL

Manufacturer

Tyco Electronics

Type

Wire Stripperr

Datasheet

1.734185-1.pdf (3 pages)

Specifications of 734185-1

Product

Crimping, Stripping & Cutting Tools & Drills

Wire Gauge Range

28-10

For Use With

PVC, THHN, THHW Wires

Lead Free Status / RoHS Status

Current page: 1 of 3
Download datasheet (2Mb)

1. INTRODUCTION

Wire Stripper 734185-1 is designed to strip wire sizes

28-10 AWG. Read these instructions thoroughly before

using the tool.

2. DESCRIPTION

The tool, which has a retracting jaw type hand

operated wire stripper, automatically strips wire sizes

28-10 AWG with minor adjustments. Wire ends can be

stripped up to 16 mm [.625 in.] and ribbon cable can

be stripped simultaneously.

3. WIRE CUTTING AND STRIPPING

TE logo and Tyco Electronics are trademarks.

*Trademark. Other products, logos, and company names might be trademarks of their respective owners.

NOTE

Front of

Tool

Upper

Stripping

Jaw

All dimensions on this document are in metric units

[with U.S. customary units in brackets].

For proper operation of the tool, jaws and insulation

must be free of lubrication.

Lower

Stripping

Jaw

Insulation Thickness

Adjustment Indicator

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

Wire Stripper 734185-1

Cutting

Blades

Figure 1

DANGER

1. Insert wire into the cutting blades and squeeze

handles to cut. See Figure 1.

2. To strip insulation, adjust the stripping blade

depth for the insulation thickness at the top of the

tool. Slide the insulation thickness adjustment

regulator as follows:

•

3. To adjust the strip length, move the wire stop by

squeezing the top tabs with fingers and sliding wire

stop to the desired measured wire length. Refer to

Figure 2.

Thin-Rear Position (toward handles)

Normal-Center Position

Thick-Forward Position

STOP

Wire

Stop

Keep fingers away from blades at all times.

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

Instruction Sheet

408-8907

05 JAN 11 Rev A

1 of 3

LOC B

734185-1 Summary of contents

Page 1

... Stripping Jaw Front of Tool Lower Stripping Jaw 1. INTRODUCTION Wire Stripper 734185-1 is designed to strip wire sizes 28-10 AWG. Read these instructions thoroughly before using the tool. All dimensions on this document are in metric units NOTE [with U.S. customary units in brackets DESCRIPTION The tool, which has a retracting jaw type hand operated wire stripper, automatically strips wire sizes 28-10 AWG with minor adjustments ...

Page 2

... Re-adjust the insulation thickness adjustment regulator and wire stop if necessary. 4. MAINTENANCE AND INSPECTION Wire Stripper 734185-1 requires no special maintenance. After use, remove stripped wire and check to ensure insulation slug has been ejected from the jaws. Store tool in a clean, dry area. ...

Page 3

... Replace the wire stop. 6. ORDERING INFORMATION / REPLACEMENT PARTS The only part that is replaceable is Wire Stripper Blade Assembly 1424946-1. Order this part or additional wire strippers through your Tyco Electronics Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 717-986-7605, or write to: CUSTOMER SERVICE (038-035) ...