NCP3125ADR2G ON Semiconductor, NCP3125ADR2G Datasheet

Page 1

NCP3125 4 A Synchronous PWM Switching Converter The NCP3125 is a flexible synchronous PWM Switching Buck Regulator. The NCP3125 is capable of producing output voltages as low as 0.8 V. The NCP3125 also incorporates voltage mode control. To reduce the ...

Page 2

VREF + 0.8 V − FB COMP Clock Ramp OSC OSC AGND Table 1. PIN DESCRIPTION Pin Pin Name 1 PGND The PGND pin is the high current ground pin for the low−side MOSFET and the ...

Page 3

Table 2. MAXIMUM RATINGS Rating Main Supply Voltage Input Bootstrap Supply Voltage vs GND Bootstrap Supply Voltage vs Ground (spikes ≤ 50 ns) Bootstrap Pin Voltage High Side Switch Max DC Current V Pin Voltage SW Switching ...

Page 4

Table 3. ELECTRICAL CHARACTERISTICS min/max values unless otherwise noted.) Characteristic Input Voltage Range Boost Voltage Range SUPPLY CURRENT Quiescent Supply Current Shutdown Supply Current Boost Quiescent Current UNDER VOLTAGE LOCKOUT V UVLO Threshold IN V UVLO Hysteresis IN SWITCHING REGULATOR ...

Page 5

3.5 3 2.5 2.0 −60 −40 − JUNCTION TEMPERATURE (°C) J Figure 4. I vs. Temperature ...

Page 6

Figure 10. Duty Cycle Maximum vs. Temperature 100 5.0 V Output 1 0.5 1 ...

Page 7

General The NCP3125 is a PWM synchronous buck regulator intended to supply load for DC−DC conversion from 5 V and 12 V buses. The NCP3125 is a regulator that has integrated high−side and low−side NMOSFETs ...

Page 8

V COMP BG TG Figure 17. Enable/Disable Driver State Diagram External Soft−Start The NCP3125 features an external soft−start function, which reduces inrush current and overshoot of the output voltage. Soft−start is achieved by using the internal current source of ...

Page 9

... ON Semiconductor has a Microsoft Excel® based design tool available online under the design tools section of the NCP3125 product page. The tool allows you to capture your design point and optimize the performance of your regulator based on your design criteria ...

Page 10

ESR of electrolytic capacitors. The ratio of ripple current to maximum output current is given in Equation Iout ...

Page 11

DCR ³ _DC RMS 2 281 mW + 4. Inductor RMS current RMS DCR = Inductor DC resistance LP = Inductor DC power dissipation CU_DC The core losses and AC ...

Page 12

In a typical converter design, the ESR of the output capacitor bank dominates the transient response. Please note that DV and DV are out of phase with each OUT−DIS OUT−ESR other, and the larger of these two voltages will determine ...

Page 13

When calculating the rise time and fall time of the high side MOSFET it is important to know the charge characteristic shown in Figure 22. Vth Figure 22. MOSFET Switching Characteristics RISE I ...

Page 14

The formula for calculating the junction temperature with the package in free air is Power dissipation of the Thermal resistance junction to ...

Page 15

... The values can be adjusted in real time using the compensation tool comp calc, available for download at ON Semiconductor’s website. The value of the feed through resistor should always be at least 2X the value of R noise. Using the 2X assumption, R ...

Page 16

0. 31 Feed through capacitor ...

Page 17

cross LC C 1.355 3.102 kHz Compensation capacitance Output capacitor ESR ESR C = Output capacitance OUT f = ...

Page 18

Assuming an output capacitance of 470 mF in parallel with 22 mF with a crossover frequency of 35 kHz, the compensation values for common output voltages can be calculated as shown in Table 6: Table 6. COMPENSATION VALUES V V ...

Page 19

ICinrush_RMS CIN ESR e 5 CIN ESR 0.316 t DELAY_TOTAL 380 0.1 W 16.45 ms 0.1W 330 0.1 W 330 mF 0.316 16.45 ...

Page 20

Output Voltage Output Current tss Figure 28. Resistive Load Current Alternatively, if the output has an under voltage lockout, turns defined voltage level, and draws a consistent current, then the RMS connected load current is ...

Page 21

... GND_IN CC COMP CP 390n 180pF 10V 50V Figure 32. Ceramic Capacitor Application 1 ORDERING INFORMATION Device NCP3125ADR2G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. BST D1 U1 NCP3125 R3 MMSD4148T1G 5 BST ...

Page 22

... *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “ ...