NCP3125 ON Semiconductor, NCP3125 Datasheet
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
NCP3125
Available stocks
Related parts for NCP3125
NCP3125 Summary of contents
Page 1
... Switching Converter The NCP3125 is a flexible synchronous PWM Switching Buck Regulator. The NCP3125 is capable of producing output voltages as low as 0.8 V. The NCP3125 also incorporates voltage mode control. To reduce the number of external components, a number of features are internally set including switching frequency. The NCP3125 is currently available in an SOIC− ...
Page 2
... UVLO POR + SCP Fault Latch − + Fault PWM R Comp PWM − Q OUT S Counter DtoA Count + Latch & − Logic VREG 0 − Fault Figure 3. NCP3125 Block Diagram Description http://onsemi.com 2 www.DataSheet4U.com BST VIN + − VOCTH − − VCC 2 V ISET PGND VSW ...
Page 3
Table 2. MAXIMUM RATINGS Rating Main Supply Voltage Input Bootstrap Supply Voltage vs GND Bootstrap Supply Voltage vs Ground (spikes ≤ 50 ns) Bootstrap Pin Voltage High Side Switch Max DC Current V Pin Voltage SW Switching ...
Page 4
Table 3. ELECTRICAL CHARACTERISTICS min/max values unless otherwise noted.) Characteristic Input Voltage Range Boost Voltage Range SUPPLY CURRENT Quiescent Supply Current Shutdown Supply Current Boost Quiescent Current UNDER VOLTAGE LOCKOUT V UVLO Threshold IN V UVLO Hysteresis IN SWITCHING REGULATOR ...
Page 5
3.5 3 2.5 2.0 −60 −40 − JUNCTION TEMPERATURE (°C) J Figure 4. I vs. Temperature ...
Page 6
Figure 10. Duty Cycle Maximum vs. Temperature 100 5.0 V Output 1 0.5 1 ...
Page 7
... General The NCP3125 is a PWM synchronous buck regulator intended to supply load for DC−DC conversion from 5 V and 12 V buses. The NCP3125 is a regulator that has integrated high−side and low−side NMOSFETs switches. The output voltage of the converter can be precisely regulated down to 800 mV ± ...
Page 8
... COMP Delay Figure 18. Soft−Start Sequence Overcurrent Threshold Setting NCP3125 overcurrent threshold can be set from 550 mV, by adding a resistor (R GND. During a short period of time following V over UVLO threshold, an internal 10 mA current (I sourced from the ISET pin, creating a voltage drop across R ...
Page 9
... ON Semiconductor has a Microsoft Excel® based design tool available online under the design tools section of the NCP3125 product page. The tool allows you to capture your design point and optimize the performance of your regulator based on your design criteria. Table 4. DESIGN PARAMETERS ...
Page 10
... In contrast, smaller values of inductance increase Selected the regulator’s maximum achievable slew rate and decrease the necessary capacitance, at the expense of higher ripple current. The peak−to−peak ripple current for NCP3125 is given by the following equation: V Ipp + D ...
Page 11
... The output capacitor must be rated to handle the ripple current at full load with proper derating. The RMS ratings given in datasheets are generally for lower switching frequency than used in switch mode power supplies, but a multiplier is usually given for higher frequency operation. The RMS current for the output capacitor can be calculated ...
Page 12
In a typical converter design, the ESR of the output capacitor bank dominates the transient response. Please note that DV and DV are out of phase with each OUT−DIS OUT−ESR other, and the larger of these two voltages will determine ...
Page 13
When calculating the rise time and fall time of the high side MOSFET it is important to know the charge characteristic shown in Figure 22. Vth Figure 22. MOSFET Switching Characteristics RISE I ...
Page 14
... To start the design, a resistor value should be chosen for R components can be chosen. A good starting value is 10 kW. The NCP3125 allows the output of the DC−DC regulator to be adjusted down to 0.8 V via an external resistor divider ³ network. The regulator will maintain 0 the feedback (eq ...
Page 15
... The values can be adjusted in real time using the compensation tool comp calc, available for download at ON Semiconductor’s website. The value of the feed through resistor should always be at least 2X the value of R noise. Using the 2X assumption, R ...
Page 16
0. 31 Feed through capacitor ...
Page 17
cross LC C 1.355 3.102 kHz Compensation capacitance Output capacitor ESR ESR C = Output capacitance OUT f = ...
Page 18
Assuming an output capacitance of 470 mF in parallel with 22 mF with a crossover frequency of 35 kHz, the compensation values for common output voltages can be calculated as shown in Table 6: Table 6. COMPENSATION VALUES V V ...
Page 19
... Equation 50. I _RMS + CLR 191 OUT V OUT I CLR_RMS OUT CR_PK ) (eq. 49) http://onsemi.com 19 www.DataSheet4U.com Load NCP3125 OUT OUT I + CR_PK OUT OUT (eq. 50) 3 330 Output resistance = Output voltage = RMS resistor current ...
Page 20
... For optimal performance, the NCP3125 should have a layout similar to the one shown in Figure 30. An important note is that the input voltage to the NCP3125 should have local decoupling to PGND. The recommended decoupling for input voltage general purpose ceramic capacitor and a 0 ...
Page 21
... VIN 10R 7 10nF FB ISET 25V 8 VSW PGND C9 C11 1nF C10 RSET 50V 0.01uF 1uF 21k 16V 16V R9 100R BST D1 U1 NCP3125 MMSD4148T1G R3 5 AGND BST 6 CBST 10R VIN COMP 10nF 7 FB ISET 25V 8 PGND VSW C9 1nF C11 50V RSET 0.01uF 21k ...
Page 22
... D 0.33 0.51 0.013 0.020 G 1.27 BSC 0.050 BSC 0.10 0.25 0.004 0.010 H J 0.19 0.25 0.007 0.010 J K 0.40 1.27 0.016 0.050 0.25 0.50 0.010 0.020 S 5.80 6.20 0.228 0.244 mm inches ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP3125/D _ ...