WFIXF1110CC.B3-998845 Cortina Systems Inc, WFIXF1110CC.B3-998845 Datasheet - Page 63
![no-image](/images/manufacturer_photos/0/1/162/cortina_systems_inc_sml.jpg)
WFIXF1110CC.B3-998845
Manufacturer Part Number
WFIXF1110CC.B3-998845
Description
IC ETHERNET MAC 10-PORT 552-BGA
Manufacturer
Cortina Systems Inc
Specifications of WFIXF1110CC.B3-998845
Controller Type
Ethernet Controller, MAC
Interface
SPI-4.2
Voltage - Supply
1.8V, 2.5V, 3.3V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
575-BCBGA Exposed Pad (552 Bumps)
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
1008-1037
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
WFIXF1110CC.B3-998845
Manufacturer:
Maxim
Quantity:
43
Company:
Part Number:
WFIXF1110CC.B3-998845
Manufacturer:
Cortina Systems Inc
Quantity:
10 000
IXF1110 MAC
Datasheet
250210, Revision 11.0
13 April 2009
Note:
5.2.3.3
5.2.4
Cortina Systems
lines with one training pattern. The sending side of the data path on both the transmit and
receive interfaces must schedule the training sequence at least once every DATA_MAX_T
cycles.
DATA_MAX_T may be set to zero, disabling periodic training on the interface (see
RX Training ($ 0x701), on page
during normal operation, and no fine-grain correction on an on-going basis is needed. This
allows the maximum possible bandwidth for data transfer. The transmit and receive
interface training sequences are scheduled independently.
Training in a Practical Implementation
The OIF Standard states that it should be possible to train and de-skew the data input in a
single training cycle. However, from the research carried out and the variances in jitter and
skew due to board layout and clock tolerance issues, some sort of averaging over several
repeated training patterns is required to reliably determine the optimal point at which to
capture the incoming data. This is true for both static alignment and dynamic phase
alignment. Therefore, several training patterns are required for an average. The more
training patterns, the more accurate the average.
The de-skew circuit in the IXF1110 MAC uses dynamic phase alignment with a typical
averaging requirement of 32 training patterns required to deliver a reliable result. During
power-on training, an unlimited number of training cycles is sent by the data sourcing
device. (The standard states that training must be sourced until a calendar has been
provisioned.) In the IXF1110 MAC, the de-skew circuit waits until completion of its
programmed average over the training patterns, ensuring that the required number of good
DIP-4s is seen. Only then is a calendar provisioned.
During periodic training, it is important to ensure that the training result is no less accurate
than that already used for the initial decision during power-on training. Thus, a similar
number of training cycles must be averaged over (32). This could make the overhead
associated with periodic training large if it is required to be carried out too often. We
therefore recommend that periodic training be scheduled infrequently (DATA_MAX_T = a
large number) and that the number of repetitions of training be = 32(α).
FIFO Status Channel
FIFO status information is sent periodically over the TSTAT link from the IXF1110 MAC to
the upper layer processor device, and over the RSTAT link from the upper layer processor
to the IXF1110 MAC. The status channels operate independently.
Figure 14
status channel is initially in the DISABLE state and sends the “1 1” pattern repeatedly. When
FIFO status transmission is enabled, there is a transition to the SYNC state and the “1 1”
framing pattern is sent. FIFO status words are then sent according to the calendar
sequence, repeating the sequence CALENDAR_M times, followed by the DIP-2 code.
®
IXF1110 10-Port 1000 Mbps Ethernet Media Access Controller
shows the operation of the FIFO status channel. The sending side of the FIFO
163). This is done when a system shows very little drift
5.2 System Packet Interface Level 4
SPI4-2
Page 63
Phase 2