ATTINY13A-SS7R Atmel, ATTINY13A-SS7R Datasheet - Page 118

• Manufacturer Part Number: ATTINY13A-SS7R
• Description: IC MCU AVR 1K FLASH 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY13A-SS7R

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -

Table 18-1.
Notes:
18.3
118
Symbol
I
CC
1. Typical values at +25°C.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. “Min” means the lowest value where the pin is guaranteed to be read as high.
4. Not tested in production.
5. Although each I/O port can under non-transient, steady state conditions sink more than the test conditions, the sum of all I
6. Although each I/O port can under non-transient, steady state conditions source more than the test conditions, the sum of all
7. Values are with external clock using methods described in
8. BOD Disabled.
Speed
ATtiny13A
(for all ports) should not exceed 60 mA. If I
not guaranteed to sink current greater than the listed test condition.
I
are not guaranteed to source current greater than the listed test condition.
is enabled (PRR = 0xFF) and there is no I/O drive.
Parameter
Supply Current,
Active Mode
Supply Current,
Idle Mode
Supply Current,
Power-Down Mode
OH
(for all ports) should not exceed 60 mA. If I
DC Characteristics, T
(7)
(7)
The maximum operating frequency of the device depends on supply voltage, V
Figure
to 4.5V.
Figure 18-1. Maximum Frequency vs. V
(8)
18-1, the relationship between maximum frequency and V
20 MHz
4 MHz
A
= -40°C to +85°C (Continued)
Condition
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
WDT enabled, V
WDT disabled, V
1.8V
OL
CC
CC
CC
CC
CC
CC
exceeds the test condition, V
OH
= 2V
= 3V
= 5V
= 2V
= 3V
= 5V
CC
CC
exceeds the test condition, V
= 3V
= 3V
“Minimizing Power Consumption” on page
CC
Min
OL
may exceed the related specification. Pins are
OH
Typ
may exceed the related specification. Pins
0.03
0.15
0.2
1.2
3.6
0.2
0.7
3.9
(1)
4.5V
CC
is linear in the range of 1.8V
Max
0.35
1.8
0.2
10
6
1
3
2
32. Power Reduction
5.5V
CC.
8126E–AVR–07/10
As shown in
Units
mA
mA
mA
mA
mA
mA
µA
µA
OL