ISE30-T1-25 SMC Corporation of America, ISE30-T1-25 Datasheet - Page 10

• Manufacturer Part Number: ISE30-T1-25
• Description: SENSOR PRESSURE 1MPA NPT/M5F NPN
• Manufacturer: SMC Corporation of America
• Series: ISE30r

Specifications of ISE30-T1-25

• Pressure Type: Vacuum
• Operating Pressure: 1.45 PSI, 1 MPa
• Port Size: Female, 1/8" (3.175mm) NPT
• Output: Digital
• Voltage - Supply: 12 V ~ 24 V
• Termination Style: Cable with Connector
• Operating Temperature: 0°C ~ 50°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 606-1000

1. Incorrect wiring can damage the switch and
2. Do not attempt to insert or pull the pressure
3. Wire separately from power lines and high
4. If a commercial switching regulator is used,
1. Do not drop, bump, or apply excessive
2. The tensile strength of the cord is 35 N.
3. Do not exceed the screw-in torque of 7 to 9
4. Do not use pressure sensors with corrosive
5. Allow a sufficient margin of tube length in
6. When a brand of tubing other than SMC is
7. The applicable fluid is air. Please consult
cause a malfunction or erroneous switch
output. Connections should be done while
the power is turned off.
sensor or its connector when the power is
on. A switch output malfunction may occur.
voltage lines, avoiding wiring in the same
conduit with these lines. Malfunctions may
occur due to noise from these other lines.
make sure that the F.G. terminal is
grounded.
impacts (980 m/s
the body of the sensor may not be damaged,
the internal parts of the sensor could be
damaged and lead to a malfunction.
Applying a greater pulling force on it can
cause a malfunction. When handling, hold
the body of the sensor––do not dangle it
from the cord.
N⋅m when installing piping. Exceeding this
value may cause malfunctioning of the
sensor.
and/or flammable gases or liquids.
piping in order to prevent application of
torsional, tensile or moment load to the
tubes and fittings.
used, make sure that the tolerance of the
tube’s
specifications.
with SMC if the switch is to be used with
other types of fluids.
Warning
Warning
1) Nylon tubing: ±0.1 mm or less
2) Soft nylon tubing: ±0.1 mm or less
3) Polyurethane tubing: +0.15 mm or less, –0.2 mm or less
O.D.
Series
Specific Product Precautions 1
Be sure to read before handling.
Connection
Handling
satisfies
2
) while handling. Although
ZSE30/ISE30
the
following
1. Mounting with panel mount adapter
2. Mounting with bracket
1. Our pressure switches are CE marked;
2. Our pressure switches do not have an
3. Do not use in an environment where static
To release push the
clips outward as shown
on the picture, and pull
back towards you.
Mount a bracket to the body using two M3 x 5L mounting
screws and install on piping with hexagon socket head cap
screws. The switch can be installed horizontally depending on
the installation location.
Panel mount
adapter
however, they are not equipped with surge
protection against lightning. Lightning surge
countermeasures should be applied directly
to system components as necessary.
explosion proof rating. Never use in the
presence of an explosive gas as this may
cause a serious explosion.
electricity can cause problems, otherwise
system failure or malfunction may result.
Warning
Caution
Operating Environment
Mounting screw
Bracket
Mounting
Panel
Tightening torque for bracket mounting
screw should be 0.5 to 0.7 N⋅m.
M3 x 5L
Panel mount
adapter
Claw
16-2-13
ZSE„
ISE„
PSE
Z
PS
Z
ZSP
ISA2
IS„
ZSM
PF2„
IF„
Data
I
I
SE3
SE
1
2