XBP09-DPUIT-156 Digi International, XBP09-DPUIT-156 Datasheet - Page 7

• Manufacturer Part Number: XBP09-DPUIT-156
• Description: MODULE XBEE PRO W/U.FL
• Manufacturer: Digi International
• Series: XBEE-PRO™r

Specifications of XBP09-DPUIT-156

• Frequency: 902MHz ~ 928MHz
• Data Rate - Maximum: 156kbps
• Modulation Or Protocol: FHSS
• Applications: ISM
• Power - Output: 17dBm (50mW)
• Sensitivity: -100dBm
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Receiving: 80mA
• Current - Transmitting: 210mA
• Data Interface: PCB, Through Hole
• Antenna Connector: U.FL
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 602-1168

XBee‐PRO® 900 RF Modules
Pin #
10
11
12
13
14
15
16
17
1
2
3
4
5
6
7
8
9
Pin Signals
DTR / SLEEP_RQ/ DIO8
PWM0 / RSSI / DIO10
Associate / DIO5/AD5
DIN / CONFIG
PWM / DIO11
ON / SLEEP
CTS / DIO7
RTS / DIO6
AD3 / DIO3
AD4/DIO4
[reserved]
RESET
Name
DIO12
DOUT
VREF
GND
Vcc
XBee‐PRO® 900 Module Mounting to an RS‐232 Interface Board.
The receptacles used on Digi development boards are manufactured by Century Interconnect.
Several other manufacturers provide comparable mounting solutions; however, Digi currently uses
the following receptacles:
Digi also recommends printing an outline of the module on the board to indicate the orientation the
module should be mounted.
Pin Assignments for the XBee‐PRO® 900 Modules
© 2009 Digi International, Inc.
• Through-hole single-row receptacles -
• Surface-mount double-row receptacles -
• Surface-mount single-row receptacles -
Samtec P/N: MMS-110-01-L-SV (or equivalent)
Century Interconnect P/N: CPRMSL20-D-0-1 (or equivalent)
Samtec P/N: SMM-110-02-SM-S
Input/Open drain
(Low‐asserted signals are distinguished with a horizontal line above signal name.)
Direction
Output
Output
output
Either
Either
Either
Either
Either
Either
Either
Either
Either
Input
-
-
-
-
be driven as an open drain/collector. The module will drive this
Module Reset (reset pulse must be at least 100 us. This must
line low when a reset occurs. This line should never be driven
This line must be connected if analog IO sampling is desired.
PWM Output 0 / RX Signal Strength Indicator / Digital IO
Request-to-Send Flow Control, Digital I/O 6
Clear-to-Send Flow Control or Digital I/O 7
Module Status Indicator or Digital I/O 9
Pin Sleep Control Line or Digital IO 8
Associated Indicator, Digital I/O 5
Must be between 2.6 V and Vcc.
PWM Output 1 / Digital I/O 11
Analog Input 4 or Digital I/O 4
Analog Input 3 or Digital I/O 3
UART Data Out
Do not connect
Description
UART Data In
Power supply
Digital I/O 12
Ground
high.)
Max Voltage
3.6V
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
n/a
Vcc
Vcc
Vcc
5V
5V
0V
5V
7