ENW-C9A02A3E Panasonic - ECG, ENW-C9A02A3E Datasheet - Page 21

• Manufacturer Part Number: ENW-C9A02A3E
• Description: MODULE ZIGBEE 2.4GHZ EMBER W/ANT
• Manufacturer: Panasonic - ECG
• Series: PAN4570r

Specifications of ENW-C9A02A3E

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -97dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 37.5mA
• Current - Transmitting: 41.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 128kB Flash, 5kB SRAM
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Rate - Maximum: -
• Other names: ENWC9A02A3E; P13685TR; PAN4570-ANT

CLASSIFICATION
Einstufung
SUBJECT
Thema
CUSTOMER’S CODE
PAN4570
23 APPLICATION NOTES
HIGH FREQUENCY PRODUCTS DIVISION
Applikationshinweise
23.1 CAUTIONS FOR SAFETY
23.2 DESIGN ENGINEERING NOTES
PANASONIC ELECTRONIC DEVICES
Sicherheitshinweise
These specifications are intended to preserve the quality assurance of products as individual
components.
Before use, check and evaluate their operation when mounted on your products. Abide by
these specifications, without deviation when using the products.These products may short-
circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated
when a short circuit occurs, then at least, provide the following failsafe functions, as a
minimum.
(1) Ensure the safety of the whole system by installing a protection circuit and a protection
(2) Ensure the safety of the whole system by installing a redundant circuit or another
Designhinweise
Heat is the major cause of shortening the life of these products. Avoid assembly and use of
the target equipment in conditions where the products' temperature may exceed the
maximum allowable.
Failure to do so may result in degrading of the product’s functions and damage to the
product.
If pulses or other transient loads (a large load applied in a short time) are applied to the
products, then before use, check and evaluate their operation when assembled on your
products.
Carefully position the products so that their heat will not burn into printed circuit boards or
affect the other components that are susceptible to heat.
Carefully locate these products so that their temperatures will not increase due to the effects
of heat generated by neighboring components.
If a vinyl-covered wire comes into contact with the products, then the cover will melt and
generate toxic gas, damaging the insulation. Never allow contact between the cover and
these products to occur.
These products are intended for general purpose and standard use in general electronic
equipment, such as home appliances, office equipment, information and communication
equipment.
These products are not intended for other uses, other than under the special conditions
shown below. Before using these products under such special conditions, check their
performance and reliability under the said special conditions carefully to determine whether
or not they can be used in such a manner.
(1) In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where
(2) In direct sunlight, outdoors, or in a dusty environment
(3) In an environment where condensation occurs.
device.
system to prevent a single fault causing an unsafe status.
liquid may splash.
(EUROPE) GmbH
Module Business
MODEM FOR IEEE802.15.4 (ZIGBEE)
“ZigBee” Modem“ (IEEE802.15.4)
PRODUCT SPECIFICATION
PANASONIC’S CODE
ENWCZA0xyzE
Produktspezifikation
APPROVED
genehmigt
No.
DS-4570-2400-102
PAGE
Seite
DATE
Datum
CHECKED
geprüft
16.03.2007
21 of 30
DESIGNED
erstellt
REV.
07