XB24-BCIT-004 Digi International/Maxstream, XB24-BCIT-004 Datasheet - Page 77

• Manufacturer Part Number: XB24-BCIT-004
• Description: MODULE 802.15.4 SER 2 CHIP ANT
• Manufacturer: Digi International/Maxstream
• Series: XBee™r

Specifications of XB24-BCIT-004

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: Home/Building Automation, Industrial Control, ZigBee™
• Power - Output: 2 mW (3 dBm)
• Sensitivity: -96dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 38mA
• Current - Transmitting: 35mA
• Data Interface: PCB, Through Hole
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -

Diagnostics
1. Node types that support the command:C = Coordinator, R = Router, E = End Device
AT Command Options
1. Node types that support the command: C = Coordinator, R = Router, E = End Device
2. Command supported by modules using AT Command firmware only
XBee ZNet 2.5/XBee‐PRO ZNet 2.5 ZigBee OEM RF Modules v1.x4x
Table 7‐07. I/O Commands
Table 7‐08. Diagnostics Commands
Table 7‐09. AT Command Options Commands
AT
Command
PR
RP
CB
AT
Command
VR
HV
%V
AT
Command
CT
CN
GT
CC
2
2
2
2
Name and Description
Set/read the bit field that configures the internal pull-up resistor status for the I/O lines.
"1" specifies the pull-up resistor is enabled. "0" specifies no pullup.(30k pull-up resistors)
Bits:"
0 - DIO4 (Pin 11)
1 - AD3 / DIO3 (Pin 17)
2 - AD2 / DIO2 (Pin 18)
3 - AD1 / DIO1 (Pin 19)
4 - AD0 / DIO0 (Pin 20)
5 - RTS / DIO6 (Pin 16)
6 - DTR / Sleep Request / DIO8 (Pin 9)
7 - DIN / Config (Pin 3)
8 - Associate / DIO5 (Pin 15)
9 - On/Sleep / DIO9 (Pin 13)
10 - DIO12 (Pin 4)
11 - PWM0 / RSSI / DIO10 (Pin 6)
12 - PWM1 / DIO11 (Pin 7)
RSSI PWM Timer. Time RSSI signal will be output after last transmission. When RP =
0xFF, output will always be on.
Commissioning Pushbutton. This command can be used to simulate commissioning
button presses in software. The parameter value should be set to the number of button
presses to be simulated. For example, sending the ATCB1 command will execute the
action associated with 1 commissioning button press. (See D0 command).
Name and Description
Firmware Version. Read firmware version of the module.
Hardware Version. Read hardware version of the module.
Supply Voltage. Reads the voltage on the Vcc pin. To convert the reading to a mV
reading, divide the read value by 1023 and multiply by 1200. A %V reading of 0x8FE
(2302 decimal) represents 2700mV or 2.70V.
Name and Description
Command Mode Timeout. Set/Read the period of inactivity (no valid commands
received) after which the RF module automatically exits AT Command Mode and returns
to Idle Mode.
Exit Command Mode. Explicitly exit the module from AT Command Mode.
Guard Times. Set required period of silence before and after the Command Sequence
Characters of the AT Command Mode Sequence (GT + CC + GT). The period of silence
is used to prevent inadvertent entrance into AT Command Mode.
Command Sequence Character. Set/Read the ASCII character value to be used
between Guard Times of the AT Command Mode Sequence (GT + CC + GT). The AT
Command Mode Sequence enters the RF module into AT Command Mode.
CC command is only applicable when using modules that contain the following “AT
Command” firmware versions: 8.0xx (Coordinator), 8.2xx (Router), 8.4xx (End Device)
© 2008 Digi International, Inc.
Node
Type
CRE
CRE
CRE
Node
Type
CRE
CRE
CRE
Node
Type
CRE
CRE
CRE
CRE
1
1
1
Parameter Range
0 - 0x1FFF
0 - 0xFF [x 100 ms]
Parameter Range
0 - 0xFFFF [read-only]
0 - 0xFFFF [read-only]
-
Parameter Range
2 - 0x028F [x 100 ms]
--
1 - 0x0CE4 [x 1 ms]
(max of 3.3 decimal sec)
0 - 0xFF
Default
0 - 0x1FFF
0x28 (40d)
Default
Factory-set
Factory-set
-
Default
0x64 (100d)
--
0x3E8
(1000d)
0x2B
(‘+’ ASCII)
76