73S1217F-EB-LITE Maxim Integrated Products, 73S1217F-EB-LITE Datasheet
73S1217F-EB-LITE
Specifications of 73S1217F-EB-LITE
Related parts for 73S1217F-EB-LITE
73S1217F-EB-LITE Summary of contents
Page 1
... TM Simplifying System Integration Evaluation Board Lite User Guide 73S1217F August 17, 2009 Rev. 1.2 UG_1217F_046 ...
Page 2
... Evaluation Board Lite User Guide © 2009 Teridian Semiconductor Corporation. All rights reserved. Teridian Semiconductor Corporation is a registered trademark of Teridian Semiconductor Corporation. Simplifying System Integration is a trademark of Teridian Semiconductor Corporation. Microsoft, Windows and Vista are registered trademarks of Microsoft Corporation. Signum is a trademark of Signum Systems Corporation. ...
Page 3
... Figure 12: 73S1217F Evaluation Board Lite Bottom View (Silkscreen) ................................................... 16 Figure 13: 73S1217F Evaluation Board Lite Top Signal Layer ................................................................ 17 Figure 14: 73S1217F Evaluation Board Lite Middle Layer 1 – Ground Plane .......................................... 17 Figure 15: 73S1217F Evaluation Board Lite Middle Layer 2 – Supply Plane ........................................... 18 Figure 16: 73S1217F Evaluation Board Lite Bottom Signal Layer ........................................................... 18 Figure 5: External Components for RESET ...
Page 4
... Smart Card Controller devices. It has been designed to operate either as a standalone or a development platform. The 73S1217F Evaluation Board Lite can be programmed to run any of the Teridian turnkey applications or a user-developed custom application. Teridian provides its USB CCID application preloaded on the board and an EMV testing application on the CD ...
Page 5
... LED 1.3 Recommended Equipment and Test Tools The following equipment and tools (not provided) are recommended for use with the 73S1217F Evaluation Board Lite package: • For functional evaluation: PC with Microsoft equipped with a USB port or an RS232 (COM) port with a DB9 connector. ...
Page 6
... A standard USB2.0 full speed interface or • A standard RS-232 serial interface (TX/RX only). The board provides by default the USB CCID application. Refer to and running the USB CCID application. Figure 2: 73S1217F Evaluation Board Lite Basic Connections 6 UG_1217F_046 Section 3 for information on setting up Rev. 1.2 ...
Page 7
... Once the file is selected, pressing the OK button loads the file into the flash memory of the IC. At this point, the emulator probe (cable) can be removed. Once the 73S1217F device is reset using the reset button on the evaluation board, the new code starts executing. ...
Page 8
... Evaluation Board Lite User Guide RESET BUTTON Figure 3: Emulator Window Showing RESET and ERASE Buttons Figure 4: Emulator Window Showing Erased Flash Memory and File Load Menu 8 UG_1217F_046 ERASE BUTTON Rev. 1.2 ...
Page 9
... DC Jack and a wall outlet. LED0 should now come on. • Connect the USB cable between the host system and the 73S1217F Evaluation Board Lite. The host system should recognize the board and start the Add New Hardware Installation wizard. When the wizard prompts, select the Microsoft Windows standard driver: Select the usbccid.inf file located in the “ ...
Page 10
... Evaluation Board Lite User Guide Installation on a Linux System Teridian has tested 73S1217F Evaluation Board -Lite with the Linux CCID driver v1.3.2 and PCSC-Lite v.1.4.4 (middleware) on two distributions of Linux: Slackware kernel 2.6.23. Refer to the 73S1215F, 73S1217F CCID USB Linux Driver Installation Guide (UG_12xxF_041) for details on the Linux software installation and usage ...
Page 11
... A: The pcsc_scan program requires the services provided by pcscd. Hence the PCSC-Lite daemon pcscd should be already running before pcsc_scan can start. Run pcscd first, and then invoke pcsc_scan. Rev. 1.2 73S1217F Evaluation Board Lite User Guide pts/2 Sl+ 16:06 0:02 pcscd –f –d ...
Page 12
... Evaluation Board Lite Hardware Description 4.1 Jumpers, Switches and Test Points Table 2 describes the 73S1217F Evaluation Board Lite jumpers, switches and modules. The Item # in Table 2 references Figure 9. The default setting refers to setup for running USB-CCID application.. Table 2: Evaluation Board Lite Jumper, Switch and Test Point Description ...
Page 13
... LED0 output LED. Test point to monitor VPC. VPC is the input power source to the internal voltage converter. This voltage is derived from either VBUS or VBAT. See the 73S1217F Data Sheet for further information. Allows the evaluation board to communicate with a smart card using a standard (credit card size) format: This slot is connected to the 73S1217F external card interface ...
Page 14
... Evaluation Board User’s Guide Figure 5: 73S1217F Evaluation Board Lite Jumper, Switch and Test Point Locations 14 ...
Page 15
... VBUS VBUS VBUS VBUS VBUS VBUS R22 100k +5VDC VCC 6 JP1 VBUS_MON GND C29 R23 Enable 0.1uF USB_CONN_4 200k Figure 6: 73S1217F Evaluation Board Lite Electrical Schematic Rev. 1.2 TP3 USR0 USR0 1 USR1 USR1 2 USR2 USR2 3 USR3 USR3 4 USR4 USR4 5 USR5 USR5 ...
Page 16
... Development Board User’s Guide 4.3 PCB Layouts Figure 7: 73S1217F Evaluation Board Lite Top View (Silkscreen) Figure 8: 73S1217F Evaluation Board Lite Bottom View (Silkscreen) 16 UG_1217F_046 Rev. 1.2 ...
Page 17
... UG_1217F_046 Figure 9: 73S1217F Evaluation Board Lite Top Signal Layer Figure 10: 73S1217F Evaluation Board Lite Middle Layer 1 – Ground Plane Rev. 1.2 73S1217F Evaluation Board Lite User Guide 17 ...
Page 18
... Development Board User’s Guide Figure 11: 73S1217F Evaluation Board Lite Middle Layer 2 – Supply Plane Figure 12: 73S1217F Evaluation Board Lite Bottom Signal Layer 18 UG_1217F_046 Rev. 1.2 ...
Page 19
... UG_1217F_046 4.4 Bill of Materials Table 3 provides the bill of materials for the 73S1217F Evaluation Board Lite schematic provided in Table 3: 73S1217F Evaluation Board Lite Bill of Materials Item Qty. Reference Part 1 3 C5,C6,C12,C16 0.47 µ 4.7 µ C10,C11,C24,C25,C26 C27,C28 5 1 C13 10 µ C14,C19,C20,C21,C22, 0.1 µF ...
Page 20
... Evaluation Board Lite User Guide Item Qty. Reference Part 21 2 R3,R22 100 kΩ 10 Ω kΩ 62 Ω R7,R9,R10,R13,R14, R15,R16,R17 680 Ω R18,R19,R24 24 Ω R20,R21 27 2 R23,R25 200 kΩ S1, TP1,TP7,TP8 HEADER TP2 HEADER TP3 HEADER MAX3237CAI 73S1217F 32.768 kHz 12.000 MHz 20 Digi-key Part ...
Page 21
... The RTC oscillator drives a standard 32.768 kHz watch crystal. Crystals of this type are accurate and do not require a high current oscillator circuit. The oscillator in the 73S1217F has been designed specifically to handle watch crystals and is compatible with their high impedance and limited power handling capability. ...
Page 22
... The PRES input on the 73S1217F contains a very weak pull down resistor result, an additional external pull down resistor is recommended to prevent any system noise from triggering a false card event. The same holds true for the PRES input, except a pull up resistor is utilized as the logic is inverted from the PRES input ...
Page 23
... Keep 10 µF and 0.1 µF capacitors close to VPC pin of the device and directly take other end to ground. • Keep 1.0 µF close to VCC pin of the smart card connector and directly take other end to ground. 1217 Rev. 1.2 73S1217F Evaluation Board Lite User Guide Figure 16: Smart Card Connections 23 ...
Page 24
... For more information about Teridian Semiconductor products or to check the availability of the 73S1217F contact us at: 6440 Oak Canyon Road Suite 100 Irvine, CA 92618-5201 Telephone: (714) 508-8800 FAX: (714) 508-8878 Email: scr.support@teridian.com For a complete list of worldwide sales offices http://www.teridian.com. 24 UG_1217F_046 Order Number 73S1217F-EB-Lite Rev. 1.2 ...
Page 25
... UG_1217F_046 Revision History Revision Date 1.0 February 6, 2008 1.1 April 6, 2009 1.2 August 17, 2009 Rev. 1.2 73S1217F Evaluation Board Lite User Guide Description First publication. Minor format changes and corrections Miscellaneous editorial modifications. Added information from the Quick Start Guide. 25 ...