STM690SM6F STMicroelectronics, STM690SM6F Datasheet - Page 15

• Manufacturer Part Number: STM690SM6F
• Description: SUPERVISOR 3V SWITCH OVER 8SOIC
• Manufacturer: STMicroelectronics
• Type: Simple Reset/Power-On Resetr

Specifications of STM690SM6F

• Number Of Voltages Monitored: 1
• Output: Push-Pull, Totem Pole
• Reset: Active Low
• Reset Timeout: 140 ms Minimum
• Voltage - Threshold: 2.925V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Monitored Voltage: 1 V to 5.5 V
• Manual Reset: Not Resettable
• Watchdog: Watchdog
• Battery Backup Switching: Backup
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1 V
• Supply Current (typ): 60 uA
• Maximum Power Dissipation: 320 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Power Fail Detection: Yes
• Threshold Voltage: 2.935V
• No. Of Supervisors / Monitors: 1
• Supply Voltage Range: 1.1V To 5.5V
• Reset Type: Active-Low
• Supply Current: 40µA
• Delay Time: 200ms
• Digital Ic Case Style: SOIC
• Rohs Compliant: Yes
• Undervoltage Threshold: 2.85 V
• Overvoltage Threshold: 3 V
• Output Type: Active Low
• Power-up Reset Delay (typ): 280 ms
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-3826-2

STM690, STM704, STM795, STM802, STM804, STM805, STM806
2.4
Note:
Note:
Backup battery switchover
In the event of a power failure, it may be necessary to preserve the contents of external
SRAM through V
automatically switch the SRAM to the backup supply when V
When the battery is first connected without V
immediately provide battery backup voltage on V
switchover operate as described below. This mode allows a battery to be attached during
manufacturing but not used until after the system has been activated for the first time. As a
result, no battery power is consumed by the device during storage and shipment. If the
backup battery is not used, connect both V
This family of supervisors does not always connect V
V
V
to have a higher voltage than V
Assuming that V
before V
external SRAMs. When V
point. V
The backup battery may be removed while V
decoupled (0.1 µF typ), without danger of triggering a reset.
Table 4.
CC
BAT
. V
Vccsw
E
V
V
PFO
RST
RST
WDI
(whichever is lower). This is done to allow the backup battery (e.g., a 3.6 V lithium cell)
V
Pin
PFI
MR
OUT
CON
BAT
E
BAT
CC
OUT
OUT
connects to V
is connected to V
gets too close to the 2.0 V minimum required to reliably retain data in most
I/O status in battery backup
Connected to V
Disconnected from V
Disabled
Logic low
High impedance
Logic high
Watchdog timer is disabled
Disabled
Logic low
Logic high
Connected to V
Logic high (STM795)
BAT
OUT
> 2.0 V, switchover at V
. With a backup battery installed with voltage V
OUT
CC
recovers, hysteresis is used to avoid oscillation around the V
(through a 100
OUT
BAT
CC
Doc ID 10519 Rev 9
CC
through a 3
through internal switch
.
OUT
BAT
SO
CC
CC
ensures that battery backup mode is entered
switch) when V
and V
PMOS power switch.
is valid, assuming V
power applied, the device does not
OUT
Status
. Only after V
OUT
BAT
to V
to V
CC
OUT
CC
CC
.
falls.
is below V
when V
CC
BAT
BAT
exceeds V
, the devices
is adequately
BAT
SW
is greater than
(2.4 V) or
RST
Operation
will the
15/42
SO