TL072ID STMicroelectronics, TL072ID Datasheet - Page 3

• Manufacturer Part Number: TL072ID
• Description: IC OP AMP JFET DUAL LNOISE 8SOIC
• Manufacturer: STMicroelectronics

Specifications of TL072ID

• Amplifier Type: J-FET
• Number Of Circuits: 2
• Slew Rate: 16 V/µs
• Gain Bandwidth Product: 4MHz
• Current - Input Bias: 20pA
• Voltage - Input Offset: 3000µV
• Current - Supply: 1.4mA
• Current - Output / Channel: 40mA
• Voltage - Supply, Single/dual (±): 6 V ~ 36 V, ±3 V ~ 18 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Number Of Channels: 2
• Common Mode Rejection Ratio (min): 80 dB
• Input Offset Voltage: 10 mV
• Input Bias Current (max): 200 pA
• Supply Current: 2.5 mA
• Maximum Power Dissipation: 680 mW
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Dual Supply Voltage: +/- 5 V, +/- 9 V, +/- 12 V, +/- 15 V
• Maximum Dual Supply Voltage: +/- 18 V
• Minimum Dual Supply Voltage: +/- 3 V
• Mounting Style: SMD/SMT
• Shutdown: No
• Technology: BiFET
• Voltage Gain Db: 106.02 dB
• Bandwidth: 4 MHz
• Channel Separation: 120
• Common Mode Rejection Ratio: 86
• Current, Input Bias: 20 pA
• Current, Input Offset: 5 pA
• Current, Output: 20 mA
• Current, Supply: 1.4 mA
• Harmonic Distortion: 0.01 %
• Number Of Amplifiers: Dual
• Package Type: SO-8
• Resistance, Input: 10^12 Ohms
• Signal Gain: 200 V/mV
• Temperature, Operating, Range: -40 to +105 °C
• Time, Rise: 0.1 μs
• Voltage, Input: ±15 V
• Voltage, Noise: 15 nV/sqrt Hz
• Voltage, Offset: 3 mV
• Voltage, Supply: 6 to 36 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

TL072 TL072A TL072B
2
Absolute maximum ratings and operating conditions
Table 1.
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts,
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-
5. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be
6. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for
7. Machine model: a 200 pF cap is charged to the specified voltage, then discharged directly between two
8. Charged device model: all pins plus package are charged together to the specified voltage and then
Table 2.
Symbol
ESD
R
R
V
supply voltages where the zero reference level is the midpoint between V
whichever is less.
circuits on all amplifiers.
limited to ensure that the dissipation rating is not exceeded.
all couples of pin combinations with other pins floating.
pins of the device with no external series resistor (internal resistor < 5 Ω). This is done for all couples of pin
combinations with other pins floating.
discharged directly to the ground.
T
V
V
Symbol
thja
CC
thjc
stg
in
id
T
V
oper
CC
Supply voltage
Input voltage
Differential input voltage
Thermal resistance junction to ambient
Thermal resistance junction to case
Output short-circuit duration
Storage temperature range
HBM: human body model
MM: machine model
CDM: charged device model
SO-8
DIP8
SO-8
DIP8
Absolute maximum ratings
Operating conditions
Supply voltage
Operating free-air temperature range
(2)
(1)
Parameter
Parameter
(7)
(3)
(6)
Absolute maximum ratings and operating conditions
(8)
(5)
(4)
(4)
TL072I, AI, BI
TL072I, AI, BI
-40 to +105
-65 to +150
CC
6 to 36
Infinite
+
±18
±15
±30
125
200
1.5
and V
85
40
41
1
TL072C, AC,
TL072C, AC,
0 to +70
CC
BC
-
.
BC
Unit
°C
V
°C/W
°C/W
Unit
°C
kV
kV
V
V
V
V
3/16