LMC6036IM/NOPB National Semiconductor, LMC6036IM/NOPB Datasheet - Page 15

• Manufacturer Part Number: LMC6036IM/NOPB
• Description: IC OP AMP 2.7V SUPP CMOS 14-SOIC
• Manufacturer: National Semiconductor
• Type: General Purpose Amplifierr

Specifications of LMC6036IM/NOPB

• Amplifier Type: General Purpose
• Number Of Circuits: 4
• Output Type: Rail-to-Rail
• Slew Rate: 1.5 V/µs
• Gain Bandwidth Product: 1.4MHz
• Current - Input Bias: 0.02pA
• Voltage - Input Offset: 500µV
• Current - Supply: 1.3mA
• Current - Output / Channel: 8mA
• Voltage - Supply, Single/dual (±): 2 V ~ 15.5 V, ±1 V ~ 7.75 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Rail/rail I/o Type: Rail to Rail Output
• Number Of Elements: 4
• Unity Gain Bandwidth Product: 1.4MHz
• Common Mode Rejection Ratio: 63dB
• Input Offset Voltage: 5mV
• Single Supply Voltage (typ): 3/5/9/12/15V
• Dual Supply Voltage (typ): Not RequiredV
• Voltage Gain In Db: 126.02dB
• Power Supply Rejection Ratio: 63dB
• Power Supply Requirement: Single
• Shut Down Feature: No
• Single Supply Voltage (min): 2V
• Single Supply Voltage (max): 15.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Technology: CMOS
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 14
• Package Type: SOIC N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Compliant
• Other names: *LMC6036IM; *LMC6036IM/NOPB; LMC6036IM

1.0 Application Notes
1.3.1 CAPACITIVE LOAD TOLERANCE
Like many other op amps, the LMC6035/6 may oscillate
when its applied load appears capacitive. The threshold of
oscillation varies both with load and circuit gain. The con-
figuration most sensitive to oscillation is a unity-gain follower.
See the Typical Performance Characteristics.
The load capacitance interacts with the op amp’s output
resistance to create an additional pole. If this pole frequency
is sufficiently low, it will degrade the op amp’s phase margin
so that the amplifier is no longer stable at low gains. As
shown in Figure 10, the addition of a small resistor
(50Ω–100Ω) in series with the op amp’s output, and a ca-
pacitor (5pF–10pF) from inverting input to output pins, re-
turns the phase margin to a safe value without interfering
with lower-frequency circuit operation. Thus, larger values of
capacitance can be tolerated without oscillation. Note that in
all cases, the output will ring heavily when the load capaci-
tance is near the threshold for oscillation.
1.4 Micro SMD Considerations
Contrary to what might be guessed, the micro SMD package
does not follow the trend of smaller packages having higher
thermal resistance. LMC6035 in micro SMD has thermal
resistance of 220˚C/W compared to 230˚C/W in MSOP. Even
when driving a 600Ω load and operating from
(b) Non-Inverting Amplifier
(a) Inverting Amplifier
(Continued)
FIGURE 9. Guard Ring Connections
01283008
±
7.5V sup-
01283009
15
plies, the maximum temperature rise will be under 4.5˚C. For
application information specific to micro SMD, see Applica-
tion note AN-1112.
Capacitive load driving capability is enhanced by using a pull
up resistor to V
conducting 500µA or more will significantly improve capaci-
tive load responses. The value of the pull up resistor must be
determined based on the current sinking capability of the
amplifier with respect to the desired output swing. Open loop
gain of the amplifier can also be affected by the pull up
resistor (see Electrical Characteristics).
FIGURE 10. Rx, Cx Improve Capacitive Load Tolerance
(d) Howland Current Pump
+
(Figure 11). Typically a pull up resistor
(c) Follower
01283005
01283010
01283011
www.national.com