MC68HC908AP64CB Freescale Semiconductor, MC68HC908AP64CB Datasheet - Page 142

• Manufacturer Part Number: MC68HC908AP64CB
• Description: IC MCU 64K FLASH 8MHZ 42SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908AP64CB

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, IRSCI, SCI, SPI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 30
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• For Use With: DEMO908AP64E - BOARD DEMO FOR 908AP64DEMO908AP64 - BOARD DEMO FOR 908AP64
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Timer Interface Module (TIM)
Setting MS0B links channels 0 and 1 and configures them for buffered PWM operation. The TIM channel
0 registers (TCH0H:TCH0L) initially control the buffered PWM output. TIM status control register 0
(TSCR0) controls and monitors the PWM signal from the linked channels.
Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM overflows. Subsequent output
compares try to force the output to a state it is already in and have no effect. The result is a 0% duty cycle
output.
Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit generates a 100% duty
cycle output. (See
9.5 Interrupts
The following TIM sources can generate interrupt requests:
9.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby modes.
9.6.1 Wait Mode
The TIM remains active after the execution of a WAIT instruction. In wait mode, the TIM registers are not
accessible by the CPU. Any enabled CPU interrupt request from the TIM can bring the MCU out of wait
mode.
If TIM functions are not required during wait mode, reduce power consumption by stopping the TIM before
executing the WAIT instruction.
9.6.2 Stop Mode
The TIM is inactive after the execution of a STOP instruction. The STOP instruction does not affect
register conditions or the state of the TIM counter. TIM operation resumes when the MCU exits stop mode
after an external interrupt.
9.7 TIM During Break Interrupts
A break interrupt stops the TIM counter.
The system integration module (SIM) controls whether status bits in other modules can be cleared during
the break state. The BCFE bit in the break flag control register (BFCR) enables software to clear status
bits during the break state. (See
142
•
•
TIM overflow flag (TOF) — The TOF bit is set when the TIM counter reaches the modulo value
programmed in the TIM counter modulo registers. The TIM overflow interrupt enable bit, TOIE,
enables TIM overflow CPU interrupt requests. TOF and TOIE are in the TIM status and control
register.
TIM channel flags (CH1F:CH0F) — The CHxF bit is set when an input capture or output compare
occurs on channel x. Channel x TIM CPU interrupt requests are controlled by the channel x
interrupt enable bit, CHxIE. Channel x TIM CPU interrupt requests are enabled when CHxIE = 1.
CHxF and CHxIE are in the TIM channel x status and control register.
9.9.4 TIM Channel Status and Control
21.5.4 SIM Break Flag Control
MC68HC908AP Family Data Sheet, Rev. 4
Registers.)
Register.)
Freescale Semiconductor