MC68HC705P6ACDW Freescale Semiconductor, MC68HC705P6ACDW Datasheet - Page 65

• Manufacturer Part Number: MC68HC705P6ACDW
• Description: IC MCU 2.1MHZ 4.5K OTP 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MC68HC705P6ACDW

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SIO
• Peripherals: POR, WDT
• Number Of I /o: 21
• Program Memory Size: 4.5KB (4.5K x 8)
• Program Memory Type: OTP
• Ram Size: 176 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Data Bus Width: 8 bit
• Data Ram Size: 176 B
• Maximum Clock Frequency: 2.1 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 16 bit
• Operating Supply Voltage: 3.3 V to 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No RoHS Version Available

11.3 MOR Programming
The contents of the MOR should be programmed in bootloader mode using the hardware shown in
Figure 10-2. MC68HC705P6A EPROM Programming
implemented bits in the MOR are essentially read-write bits in bootloader mode as shown in
The programming of the MOR is the same as user EPROM.
A sample routine to program a byte of EPROM is shown in
Once the MOR bits have been programmed, the options are not loaded into the MOR registers until the
part is reset.
Freescale Semiconductor
1. Set the ELAT bit in the EPROG register.
2. Write the desired data to the desired MOR address.
3. Set the EPGM bit in the EPROG.
4. Wait for the programming time (t
5. Clear the ELAT and EPGM bits in the EPROG.
6. Remove the programming voltage from the IRQ/V
001C
00FF
0023
1EFF
1F00
0000
00E0
00E0
00E2
00E4
00E6
00E9
00EB
00ED
00EF
A6 04
B7 1C
A6 FF
C7 1E FF
12 1C
AD 03
3F 1C
81
MC68HC705P6A Advance Information Data Sheet, Rev. 2.1
Table 11-2. MOR Programming Routine
EPROG
DATA2
DATA1
MOR2
MOR1
EPGM
EPGM
EQU
EQU
EQU
EQU
EQU
EQU
ORG
LDA
STA
LDA
STA
BSET EPGM,EPROG
BSR
CLR
RTS
).
$1C
$FF
#23
$1EFF
$1F00
$00
$E0
#$04
EPROG
#DATA2
MOR2
DELAY
EPROG
Flowchart. In order to allow programming, all the
PP
Table
pin.
PROGRAMMING REG
SAMPLE MOR VALUES
MOPR ADDRESSES
EPGM BIT IN EPROG REG
SET ELAT BIT
IN EPGM REG AT $1C
DATA BYTE
WRITE IT TO MOR LOC
TURN ON PGM VOLTAGE
WAIT 4 ms MINIMUM
CLR EPGM REGISTER
11-2.
MOR Programming
Figure
11-1.
65