ATTINY87-15XZ Atmel, ATTINY87-15XZ Datasheet - Page 244

• Manufacturer Part Number: ATTINY87-15XZ
• Description: MCU AVR 8K FLASH 15MZ 20-TSSOP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY87-15XZ

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 20-TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T
Notes:
244
A
Symbol
I
I
R
R
I
V
I
t
IL
IH
CC
ACLK
ACID
= -40°C to +125°C, Vcc = 2.7V to 5.5V (unless otherwise noted) (Continued)
ACIO
RST
pu
1. “Typ.", typical values at 25°C. Maximum values are characterized values and not test limits in production.
2. "Max.” means the highest value where the pin is guaranteed to be read as low.
3. “Min.” means the lowest value where the pin is guaranteed to be read as high.
4. Although each I/O port can sink more than the test conditions (10 mA at Vcc= 5V, 5 mA at Vcc = 3V) under steady state con-
5. Although each I/O port can source more than the test conditions (10 mA at Vcc = 5V, 5 mA at Vcc = 3V) under steady state
6. Values using methods described in
7. BOD Disabled.
ATtiny87/ATtiny167
ditions (non-transient), the following must be observed:
- The sum of all IOL, for all ports, should not exceed 120 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
conditions (non-transient), the following must be observed:
- The sum of all IOH, for all ports, should not exceed 120 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
(PRR = 0xFF) and there is no I/O drive.
Parameter
Input Leakage
Current I/O Pin
Input Leakage
Current I/O Pin
Reset Pull-up Resistor
I/O Pin Pull-up Resistor
Power Supply Current
Active Mode
(external clock)
Power Supply Current
Idle Mode
(external clock)
Power Supply Current
Power-down Mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
Common Mode Vcc/2
(6)
(6)
(7)
Vcc = 5.5V, pin low
(absolute value)
Vcc = 5.5V, pin high
(absolute value)
16 MHz, Vcc = 5V
8 MHz, Vcc = 5V
8 MHz, Vcc = 3V
4 MHz, Vcc = 3V
16 MHz, Vcc = 5V
8 MHz, Vcc = 5V
8 MHz, Vcc = 3V
4 MHz, Vcc = 3V
WDT enabled, Vcc = 5V
WDT disabled, Vcc = 5V
WDT enabled, Vcc = 3V
WDT disabled, Vcc = 3V
Vcc = 5V
V
Vcc = 5V
V
Vcc = 2.7V
Vcc = 5.0V
Condition
in
in
= Vcc/2
= Vcc/2
“Minimizing Power Consumption” on page
Min.
-10
-50
30
20
45. Power Reduction is enabled
Typ.
< 0.05
< 0.05
0.18
0.15
170
180
5.5
2.8
1.8
3.5
1.8
0.5
10
10
1
7
5
(1)
Max.
100
7.0
3.5
2.5
5.0
2.5
1.5
0.8
60
50
13
70
70
45
40
50
1
1
7728G–AVR–06/10
Units
mA
mA
mA
mA
mA
mA
mA
mA
mV
µA
µA
µA
µA
µA
µA
nA
k
k
ns
ns