ATMEGA169-16AU Atmel, ATMEGA169-16AU Datasheet - Page 235

• Manufacturer Part Number: ATMEGA169-16AU
• Description: IC AVR MCU 16K 16MHZ 5V 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• For Use With: ATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SAMPLE_PRELOAD; 0x2
AVR_RESET; 0xC
BYPASS; 0xF
Boundary-scan Related
Register in I/O Memory
MCU Control Register –
MCUCR
2514P–AVR–07/06
Mandatory JTAG instruction for pre-loading the output latches and taking a snap-shot of
the input/output pins without affecting the system operation. However, the output latches
are not connected to the pins. The Boundary-scan Chain is selected as Data Register.
The active states are:
•
•
•
The AVR specific public JTAG instruction for forcing the AVR device into the Reset
mode or releasing the JTAG reset source. The TAP controller is not reset by this instruc-
tion. The one bit Reset Register is selected as Data Register. Note that the reset will be
active as long as there is a logic “one” in the Reset Chain. The output from this chain is
not latched.
The active states are:
•
Mandatory JTAG instruction selecting the Bypass Register for Data Register.
The active states are:
•
•
The MCU Control Register contains control bits for general MCU functions.
• Bit 7 – JTD: JTAG Interface Disable
When this bit is zero, the JTAG interface is enabled if the JTAGEN Fuse is programmed.
If this bit is one, the JTAG interface is disabled. In order to avoid unintentional disabling
or enabling of the JTAG interface, a timed sequence must be followed when changing
this bit: The application software must write this bit to the desired value twice within four
cycles to change its value. Note that this bit must not be altered when using the On-chip
Debug system.
If the JTAG interface is left unconnected to other JTAG circuitry, the JTD bit should be
set to one. The reason for this is to avoid static current at the TDO pin in the JTAG
interface.
Bit
Read/Write
Initial Value
Capture-DR: Data on the external pins are sampled into the Boundary-scan Chain.
Shift-DR: The Boundary-scan Chain is shifted by the TCK input.
Update-DR: Data from the Boundary-scan chain is applied to the output latches.
However, the output latches are not connected to the pins.
Shift-DR: The Reset Register is shifted by the TCK input.
Capture-DR: Loads a logic “0” into the Bypass Register.
Shift-DR: The Bypass Register cell between TDI and TDO is shifted.
R/W
JTD
7
0
R
6
–
0
R
5
–
0
PUD
R/W
4
0
R
3
–
0
R
2
–
0
ATmega169/V
IVSEL
R/W
1
0
IVCE
R/W
0
0
MCUCR
235