AT90S4433-8AI Atmel, AT90S4433-8AI Datasheet - Page 91
![IC MCU 4K 8MHZ A/D IT 32TQFP](/photos/6/91/69154/313-32-tqfp_sml.jpg)
AT90S4433-8AI
Manufacturer Part Number
AT90S4433-8AI
Description
IC MCU 4K 8MHZ A/D IT 32TQFP
Manufacturer
Atmel
Series
AVR® 90Sr
Datasheet
1.AT90S4433-8AC.pdf
(126 pages)
Specifications of AT90S4433-8AI
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
4KB (2K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 6x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
32-TQFP, 32-VQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90S4433-8AI
Manufacturer:
ATMEL
Quantity:
24
Company:
Part Number:
AT90S4433-8AI
Manufacturer:
ATMEL
Quantity:
30
Part Number:
AT90S4433-8AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Programming the Fuse Bits
Programming the Lock Bits
Reading the Fuse and Lock
Bits
1042H–AVR–04/03
The algorithm for programming the Fuse bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
A: Load Command “0100 0000”.
B: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
1. Give WR a t
The algorithm for programming the Lock bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
A: Load Command “0010 0000”.
B: Load Data Low Byte. Bit n = “0” programs the Lock bit.
C: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
The algorithm for reading the Fuse and Lock bits is as follows (refer to “Programming
the Flash” for details on command loading):
A: Load Command “0000 0100”.
1. Set OE to “0”, and BS to “0”. The status of the Fuse bits can now be read at
2. Set BS to “1”. The status of the Lock bits can now be read at DATA (“0” means
3. Set OE to “1”.
Bit 5 = SPIEN Fuse bit
Bit 4 = BODLEVEL Fuse bit
Bit 3 = BODEN Fuse bit
Bit 2 = CKSEL2 Fuse bit
Bit 1 = CKSEL1 Fuse bit
Bit 0 = CKSEL0 Fuse bit
Bits 7 - 6 = “1”. These bits are reserved and should be left unprogrammed (“1”).
is found in Table 33. Programming the Fuse bits does not generate any activity
on the RDY/BSY pin.
Bit 2 = Lock bit 2
Bit 1 = Lock bit 1
Bits 7 - 3, 0 = “1”. These bits are reserved and should be left unprogrammed (“1”).
DATA (“0” means programmed).
Bit 5 = SPIEN Fuse bit
Bit 4 = BODLEVEL Fuse bit
Bit 3 = BODEN Fuse bit
Bit 2 = CKSEL2 Fuse bit
Bit 1 = CKSEL1 Fuse bit
Bit 0 = CKSEL0 Fuse bit
programmed).
Bit 2 = Lock Bit 2
Bit 1= Lock Bit 1
WLWH_PFB
wide negative pulse to execute the programming, t
AT90S/LS4433
WLWH_PFB
91