C8051F062-GQR Silicon Laboratories Inc, C8051F062-GQR Datasheet - Page 79

• Manufacturer Part Number: C8051F062-GQR
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F062-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 59
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b, 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: 336-1214 - DEV KIT FOR F060/F062/F063
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

6.6.
The DMA contains multiple interrupt sources. Some of these can be individually enabled to generate inter-
rupts as necessary. The DMA Control Register (DMA0CN, Figure 6.4) and DMA Configuration Register
(DMA0CF, Figure 6.5) contain the enable bits and flags for the DMA interrupt sources. When an interrupt is
enabled and the interrupt condition occurs, a DMA interrupt will be generated (EIE2.7 is set to ‘1’).
The DMA flags that can generate a DMA0 interrupt are:
6.7.
The data paths from the ADCs to XRAM are double-buffered when using the DMA interface. When a con-
version is completed by the ADC, it first enters the ADCs data register. If the DMA’s data buffer is empty,
the conversion results will immediately be written into the DMA’s internal data buffer for that ADC. Data in
the DMA’s internal data buffer is written to XRAM at the first available opportunity (see
Addressing and Setup” on page
the DMA’s data buffer until data in the buffer has been written to XRAM. When a conversion is completed
and the DMA’s data buffer is not empty, an overflow warning flag is generated. If a second conversion data
word becomes available before the DMA’s data buffer is written to XRAM, the data in the ADC’s data regis-
ters is over-written with the new data word, and a data overflow error flag is generated.
Interrupt Sources
1. DMA Operations Complete (DMA0CN.6, DMA0INT) occurs when all DMA operations have
2. ADC1 Data Overflow Error (DMA0CN.4, DMA0DE1) occurs when the DMA interface cannot
3. ADC0 Data Overflow Error (DMA0CN.3, DMA0DE0) occurs when the DMA interface cannot
4. ADC1 Data Overflow Warning (DMA0CN.1, DMA0DO1) occurs when data from ADC0
5. ADC0 Data Overflow Warning (DMA0CN.0, DMA0DO0) occurs when data from ADC1
6. Repeat Counter Overflow (DMA0CF.2, DMA0CI) occurs when the Repeat Counter reaches
7. End Of Operation (DMA0CF.0, DMA0EO) occurs when an End Of Operation instruction is
Data Buffer Overflow Warnings and Errors
been completed, and the DMA interface is idle.
access XRAM for two conversion cycles of ADC1. This flag indicates that at least one conver-
sion result from ADC1 has been discarded.
access XRAM for two conversion cycles of ADC0. This flag indicates that at least one conver-
sion result from ADC0 has been discarded.
becomes available and the DMA has not yet written the previous results to XRAM. This inter-
rupt source can be enabled and disabled with the Data Overflow Warning Enable bit
(DMA0CN.2, DMA0DOE).
becomes available and the DMA has not yet written the previous results to XRAM. This inter-
rupt source can be enabled and disabled with the Data Overflow Warning Enable bit
(DMA0CN.2, DMA0DOE).
the Repeat Counter Limit. This interrupt source can be enabled and disabled with the Repeat
Counter Overflow Interrupt Enable bit (DMA0CF.3, DMA0CIE).
reached in the Instruction Buffer. This interrupt source can be enabled and disabled with the
End Of Operation Interrupt Enable bit (DMA0CF.1, DMA0EOE).
76). Conversion results from the ADC’s data registers are not copied into
Rev. 1.2
C8051F060/1/2/3/4/5/6/7
Section “6.3. XRAM
79