C8051F010-GQ Silicon Laboratories Inc, C8051F010-GQ Datasheet - Page 102
![IC 8051 MCU 32K FLASH 64TQFP](/photos/12/39/123946/c8051f010-gq_sml.jpg)
C8051F010-GQ
Manufacturer Part Number
C8051F010-GQ
Description
IC 8051 MCU 32K FLASH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F01xr
Specifications of C8051F010-GQ
Core Processor
8051
Core Size
8-Bit
Speed
20MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
32
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x10b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TQFP, 64-VQFP
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
I2C, SMBus, SPI, UART
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
32
Number Of Timers
4 bit
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F005DK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
On-chip Dac
12 bit, 2 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
336-1191
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F010-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
14.1.
If a crystal or ceramic resonator were used to generate the system clock for the MCU, the circuit would be as shown
in Figure 14.1, Option 1. For an ECS-110.5-20-4 crystal, the resonate frequency is 11.0592MHz, the intrinsic
capacitance is 7pF, and the ESR is 60. The compensation capacitors should be 33pF each, and the PWB parasitic
capacitance is estimated to be 2pF. The appropriate External Oscillator Frequency Control value (XFCN) from the
Crystal column in the table in Figure 14.3 (OSCXCN Register) should be 111b.
Because the oscillator detect circuitry needs time to settle after the crystal oscillator is enabled, software should wait
at least 1ms between enabling the crystal oscillator and polling the XTLVLD bit. The recommend procedure is:
1. Enable the external oscillator
2. Wait at least 1 ms
3. Poll for XTLVLD '0' ==> '1'
4. Switch to the external oscillator
Switching to the external oscillator before the crystal oscillator has stabilized could result in unpredictable behavior.
NOTE: Crystal oscillator circuits are quite sensitive to PCB layout. The crystal should be placed as close as possible
to the XTAL pins on the device, keeping the traces as short as possible and shielded with ground plane from any
other traces which could introduce noise or interference.
14.2.
If an external RC network were used to generate the system clock for the MCU, the circuit would be as shown in
Figure 14.1, Option 2. The capacitor must be no greater than 100pF, but using a very small capacitor will increase
the frequency drift due to the PWB parasitic capacitance. To determine the required External Oscillator Frequency
Control value (XFCN) in the OSCXCN Register, first select the RC network value to produce the desired frequency
of oscillation. If the frequency desired is 100kHz, let R = 246k and C = 50pF:
14.3.
If an external capacitor were used to generate the system clock for the MCU, the circuit would be as shown in
Figure 14.1, Option 3. The capacitor must be no greater than 100pF, but using a very small capacitor will increase
the frequency inaccuracy due to the PWB parasitic capacitance. To determine the required External Oscillator
Frequency Control value (XFCN) in the OSCXCN Register, select the capacitor to be used and find the frequency
of oscillation from the equations below. Assume AV+ = 3.0V and C = 50pF:
If a frequency of roughly 90kHz is desired, select the K Factor from the table in Figure 14.3 as KF = 13:
Therefore, the XFCN value to use in this example is 011.
f = 1.23(10
XFCN log
XFCN log
XFCN 2, or code 010
f = KF / (C * VDD) = KF / (50 * 3)
f = KF / 150
f = 13 /150 = 0.087MHz, or 87kHz
External Crystal Example
External RC Example
External Capacitor Example
3
)/RC = 1.23(10
2
2
(f/25kHz)
(100kHz/25kHz) = log
3
) / [246 * 50] = 0.1MHz = 100kHz
2
(4)
Rev. 1.7
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
102