MC56F8322VFAE Freescale Semiconductor, MC56F8322VFAE Datasheet - Page 54

• Manufacturer Part Number: MC56F8322VFAE
• Description: IC DSP 16BIT 60MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8322VFAE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Program Memory Size: 40KB (20K x 16)
• Program Memory Type: FLASH
• Ram Size: 6K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F83xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 40 MIPs
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 21
• Data Ram Size: 4 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Interface Type: SCI, SPI, CAN
• Minimum Operating Temperature: - 40 C
• For Use With: MC56F8323EVME - BOARD EVALUATION MC56F8323
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.8 Factory-Programmed Memory
The Boot Flash memory block is programmed during manufacturing with a default Serial Bootloader
program. The Serial Bootloader application can be used to load a user application into the Program and
Data Flash (not available on the 56F8122) memories of the device. The 56F83xx SCI/CAN Bootloader
User Manual provides detailed information on this firmware. An application note, Production Flash
Programming, details how the Serial Bootloader program can be used to perform production Flash
programming of the on-board Flash memories as well as other optional methods.
Like all the Flash memory blocks, the Boot Flash can be erased and programmed by the user. The Serial
Bootloader application is programmed as an aid to the end user, but is not required to be used or maintained
in the Boot Flash memory.
Part 5 Interrupt Controller (ITCN)
5.1 Introduction
The Interrupt Controller (ITCN) module is used to arbitrate between various interrupt requests (IRQs), to
signal to the 56800E core when an interrupt of sufficient priority exists, and to what address to jump in
order to service this interrupt.
5.2 Features
The ITCN module design includes these distinctive features:
For further information, see
5.3 Functional Description
The Interrupt Controller is a slave on the IPBus. It contains registers allowing each of the 82 interrupt
sources to be set to one of four priority levels, excluding certain interrupts of fixed priority. Next, all of
the interrupt requests of a given level are priority encoded to determine the lowest numerical value of the
active interrupt requests for that level. Within a given priority level, 0 is the highest priority, while number
81 is the lowest.
5.3.1
Once the ITCN has determined that an interrupt is to be serviced and which interrupt has the highest
priority, an interrupt vector address is generated. Normal interrupt handling concatenates the VBA and the
vector number to determine the vector address. In this way, an offset is generated into the vector table for
each interrupt.
54
•
•
•
•
Programmable priority levels for each IRQ
Two programmable Fast Interrupts
Notification to SIM module to restart clocks out of Wait and Stop modes
Drives initial address on the address bus after reset
Normal Interrupt Handling
Table
4-3, Interrupt Vector Table Contents.
56F8322 Techncial Data, Rev. 16
Freescale Semiconductor
Preliminary