C8051F019-GQ Silicon Laboratories Inc, C8051F019-GQ Datasheet - Page 114
![IC 8051 MCU 16K FLASH 48TQFP](/photos/12/38/123852/c8051f019-gq_sml.jpg)
C8051F019-GQ
Manufacturer Part Number
C8051F019-GQ
Description
IC 8051 MCU 16K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F018r
Specifications of C8051F019-GQ
Program Memory Type
FLASH
Program Memory Size
16KB (16K x 8)
Package / Case
48-TQFP, 48-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
16
Number Of Timers
4
Operating Supply Voltage
2.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F005DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
No. Of I/o's
16
Ram Memory Size
1.25KB
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1198
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F019-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
16.1.
The UART provides four operating modes (one synchronous and three asynchronous) selected by setting
configuration bits in the SCON register. These four modes offer different baud rates and communication protocols.
The four modes are summarized in Table 16.1 below. Detailed descriptions follow.
16.1.1. Mode 0: Synchronous Mode
Mode 0 provides synchronous, half-duplex communication. Serial data is transmitted and received on the RX pin.
The TX pin provides the shift clock for both transmit and receive. The MCU must be the master since it generates
the shift clock for transmission in both directions (see the interconnect diagram in Figure 16.2).
Eight data bits are transmitted/received, LSB first (see the timing diagram in Figure 16.3). Data transmission begins
when an instruction writes a data byte to the SBUF register. The TI Transmit Interrupt Flag (SCON.1) is set at the
end of the eighth bit time. Data reception begins when the REN Receive Enable bit (SCON.4) is set to logic 1 and
the RI Receive Interrupt Flag (SCON.0) is cleared. One cycle after the eighth bit is shifted in, the RI flag is set and
reception stops until software clears the RI bit. An interrupt will occur if enabled when either TI or RI is set.
The Mode 0 baud rate is the system clock frequency divided by twelve. RX is forced to open-drain in mode 0, and
an external pull-up will typically be required.
Mode
0
1
2
3
UART Operational Modes
RX (data out)
Synchronization
RX (data in)
Asynchronous
Asynchronous
Asynchronous
TX (clk out)
TX (clk out)
Synchronous
C8051Fxxx
Figure 16.3. UART Mode 0 Timing Diagram
Figure 16.2. UART Mode 0 Interconnect
D0
Timer 1 or Timer 2 Overflow
Timer 1 or Timer 2 Overflow
SYSCLK/32 or SYSCLK/64
D0
RX
Table 16.1. UART Modes
TX
D1
SYSCLK/12
Baud Clock
D1
MODE 0 TRANSMIT
MODE 0 RECEIVE
Rev. 1.2
D2
D2
D3
D3
CLK
DATA
D4
8 Extra Outputs
D4
Data Bits
D5
8
8
9
9
D5
Reg.
Shift
D6
D6
Start/Stop Bits
1 Start, 1 Stop
1 Start, 1 Stop
1 Start, 1 Stop
C8051F018
C8051F019
None
D7
D7
114