MCHC908GR8AMFAER Freescale Semiconductor, MCHC908GR8AMFAER Datasheet - Page 90

• Manufacturer Part Number: MCHC908GR8AMFAER
• Description: IC MCU 8K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8AMFAER

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Internal Clock Generator (ICG) Module)
;* Clock Monitor Enable Code Example
;* This code turns on both clocks, selects the desired one,
;*
;*
CMEnable:
7.4.3 Using Clock Monitor Interrupts
The clock monitor circuit can be used to recover from perilous situations such as crystal loss. To use the
clock monitor effectively, these points should be observed:
7.4.4 Quantization Error in DCO Output
The digitally controlled oscillator (DCO) is comprised of three major sub-blocks:
Each of these blocks affects the clock period of the internal clock (ICLK). Since these blocks are controlled
by the digital loop filter (DLF) outputs DDIV and DSTG, the output of the DCO can change only in
90
1. Binary weighted divider
2. Variable-delay ring oscillator
3. Ring oscillator fine-adjust circuit
•
•
•
•
•
•
•
•
•
then turns on the Clock Monitor and CM Interrupt
ICG Clock Monitor Enable
Enable the clock monitor and clock monitor interrupts.
The first statement in the clock monitor interrupt service routine (CMISR) should be a read to the
ICG control register (ICGCR) to verify that the clock monitor flag (CMF) is set. This is also the first
step in clearing the CMF bit.
The second statement in the CMISR should be a write to the ICGCR to clear the CMF bit (write the
bit low). Writing the bit high will not affect it. This statement does not need to immediately follow
the first, but must be contained in the CMISR.
The third statement in the CMISR should be to clear the CMON bit. This is required to ensure
proper reconfiguration of the reference dividers. This statement also must be contained in the
CMISR.
Although the clock monitor can be enabled only when both clocks are stable (ICGS is set or ECGS
is set), it will remain set if one of the clocks goes unstable.
The clock monitor only works if the external slow (EXTSLOW) bit in the CONFIG2 register is set to
the correct value.
The internal and external clocks must both be enabled and running to use the clock monitor.
When the clock monitor detects inactivity, the inactive clock is automatically deselected and the
active clock selected as the source for CGMXCLK and TBMCLK. The CMISR can use the state of
the CS bit to check which clock is inactive.
When the clock monitor detects inactivity, the application may have been subjected to extreme
conditions which may have affected other circuits. The CMISR should take any appropriate
precautions.
bset
brclr
bset
bset
bset
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
Figure 7-10. Code Example for Enabling the Clock Monitor
ECGON,ICGCR
ECGS,ICGCR,*
CS,ICGCR
CMON,ICGCR
CMIE,ICGCR
; turn on external oscillator
;
; wait until external clock engaged
; select external clock for bus
; enable Clock Monitor
; enable CM interrupt
(assumes internal osc is on)
Freescale Semiconductor