C8051T612-GQ Silicon Laboratories Inc, C8051T612-GQ Datasheet - Page 103
![IC 8051 MCU 8K BYTE-PROG 32-LQFP](/photos/12/34/123409/c8051t612-gq_sml.jpg)
C8051T612-GQ
Manufacturer Part Number
C8051T612-GQ
Description
IC 8051 MCU 8K BYTE-PROG 32-LQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051T61xr
Specifications of C8051T612-GQ
Program Memory Type
OTP
Program Memory Size
8KB (8K x 8)
Package / Case
32-LQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, Temp Sensor, WDT
Number Of I /o
29
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 21x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
29
Number Of Timers
4
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051FT610DK
Minimum Operating Temperature
- 40 C
On-chip Adc
21-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1439
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T612-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051T612-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
SFR Definition 19.1. VDM0CN: V
SFR Address = 0xFF
19.3. External Reset
The external RST pin provides a means for external circuitry to force the device into a reset state. Assert-
ing an active-low signal on the RST pin generates a reset; an external pullup and/or decoupling of the RST
pin may be necessary to avoid erroneous noise-induced resets. See Table 7.4 for complete RST pin spec-
ifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
19.4. Missing Clock Detector Reset
The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system
clock remains high or low for more than the missing clock detector timeout, the one-shot will generate a
reset. After a MCD reset, the MCDRSF flag (RSTSRC.2) will read 1, signifying the MCD as the reset
source; otherwise, this bit reads 0. Writing a 1 to the MCDRSF bit enables the Missing Clock Detector; writ-
ing a 0 disables it. The state of the RST pin is unaffected by this reset.
Name
Reset
Bit
5:0
Type
7
6
Bit
VDDSTAT
VDMEN
Unused
VDMEN
Name
Varies
R/W
7
VDDSTAT
V
This bit turns the V
tem resets until it is also selected as a reset source in register RSTSRC (SFR Def-
inition 19.2). Selecting the V
may generate a system reset. In systems where this reset would be undesirable, a
delay should be introduced between enabling the V
reset source. See Table 7.4 for the minimum V
0: V
1: V
V
This bit indicates the current power supply status (V
0: V
1: V
Unused. Read = 000000b; Write = Don’t care.
Varies
DD
DD
R
6
DD
DD
DD
DD
Monitor Enable.
Status.
Monitor Disabled.
Monitor Enabled.
is at or below the V
is above the V
R
5
0
DD
DD
DD
monitor circuit on/off. The V
Monitor Control
monitor threshold.
DD
Rev 1.0
R
4
0
DD
monitor threshold.
monitor as a reset source before it has stabilized
C8051T610/1/2/3/4/5/6/7
Function
R
3
0
DD
DD
Monitor turn-on time.
R
2
0
DD
DD
Monitor cannot generate sys-
Monitor and selecting it as a
Monitor output).
R
1
0
R
0
0
103