MC9S08MP16VLF Freescale Semiconductor, MC9S08MP16VLF Datasheet - Page 9

• Manufacturer Part Number: MC9S08MP16VLF
• Description: MCU 8BIT .25U SGF FLASH 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08MP16VLF

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 51.34MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 40
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x12b, D/A 3x5b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Processor Series: S08MP
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI
• Maximum Clock Frequency: 51.34 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 2
• Operating Supply Voltage: - 0.3 V to + 5.8 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08MP16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 13 Channel
• On-chip Dac: 3 DAC, 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.2
The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better
understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate:
2.3
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the
limits specified in
conditions, refer to the remaining tables in this section.
This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised
that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this
high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for
instance, either V
Freescale Semiconductor
P
C
D
T
Parameter Classification
Absolute Maximum Ratings
1
2
3
Those parameters that are guaranteed during production testing on each individual device.
Those parameters that are achieved by the design characterization by measuring a statistically relevant
sample size across process variations.
Those parameters that are achieved by design characterization on a small sample size from typical
devices under typical conditions unless otherwise noted. All values shown in the typical column are within
this category.
Those parameters that are derived mainly from simulations.
Supply voltage
Maximum current into V
Digital input voltage
Instantaneous maximum current
Storage temperature range
SS
current-limiting resistor, calculate resistance values for positive (V
voltages, then use the larger of the two resistance values.
All functional non-supply pins, except for PTF1/RESET are internally clamped to V
Power supply must maintain regulation within operating V
operating maximum current conditions. If positive injection current (V
I
out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
The classification is shown in the column labeled “C” in the parameter tables where
appropriate.
Input must be current limited to the value specified. To determine the value of the required
DD
Table 3
Single pin limit (applies to all port pins)
or V
, the injection current may flow out of V
DD
may affect device reliability or cause permanent damage to the device. For functional operating
) or the programmable pull-up resistor associated with the pin is enabled.
Rating
DD
Table 3. Absolute Maximum Ratings
MC9S08MP16 Series Data Sheet, Rev. 1
Table 2. Parameter Classifications
DD
load will shunt current greater than maximum injection
1, 2, 3
NOTE
DD
and could result in external power supply going
Symbol
V
T
I
V
DD
I
DD
stg
D
In
DD
range during instantaneous and
DD
–0.3 to V
) and negative (V
–0.3 to +5.8
In
–55 to 150
> V
Value
± 25
120
DD
DD
) is greater than
+ 0.3
SS
Electrical Characteristics
SS
and V
) clamp
Unit
mA
mA
°C
V
V
DD
.
9