C8051T605-GS Silicon Laboratories Inc, C8051T605-GS Datasheet - Page 58
![IC 8051 MCU 2K-EEPROM 14-SOIC](/photos/12/33/123368/c8051t605-gs_sml.jpg)
C8051T605-GS
Manufacturer Part Number
C8051T605-GS
Description
IC 8051 MCU 2K-EEPROM 14-SOIC
Manufacturer
Silicon Laboratories Inc
Series
C8051T60xr
Datasheet
1.C8051T600EDB.pdf
(188 pages)
Specifications of C8051T605-GS
Program Memory Type
OTP
Program Memory Size
2KB (2K x 8)
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051T6x
Core
8051
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
I2C/SMBus/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
8
Number Of Timers
3
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051T600DK
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1404 - KIT DEV FOR C8051T60X MCU'S
Eeprom Size
-
Data Converters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1661-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051T605-GS
Manufacturer:
Silicon Laboratories Inc
Quantity:
135
C8051T600/1/2/3/4/5/6
SFR Definition 12.1. REG0CN: Voltage Regulator Control
SFR Address = 0xC7
58
Name
Reset
5:1
Bit
Type
7
6
0
Bit
Reserved Reserved. Must Write 00000b.
STOPCF Stop Mode Configuration.
BYPASS Bypass Internal Regulator.
MPCE
Name
STOPCF
R/W
7
0
This bit configures the regulator’s behavior when the device enters STOP mode.
0: Regulator is still active in STOP mode. Any enabled reset source will reset the
device.
1: Regulator is shut down in STOP mode. Only the RST pin or power cycle can reset
the device.
This bit places the regulator in bypass mode, turning off the regulator, and allowing the
core to run directly from the V
0: Normal Mode—Regulator is on.
1: Bypass Mode—Regulator is off, and the microcontroller core operates directly from
the V
IMPORTANT: Bypass mode is for use with an external regulator as the supply
voltage only. Never place the regulator in bypass mode when the V
voltage is greater than the specifications given in Table 8.1 on page 30. Doing so
may cause permanent damage to the device.
Memory Power Controller Enable.
This bit can help the system save power at slower system clock frequencies (about
2.0 MHz or less) by automatically shutting down the EPROM memory between clocks
when information is not being fetched from the EPROM memory.
0: Normal Mode—Memory power controller disabled (EPROM memory is always on).
1: Low Power Mode—Memory power controller enabled (EPROM memory turns on/off
as needed).
Note: If an external clock source is used with the Memory Power Controller enabled, and the
BYPASS
DD
R/W
clock frequency changes from slow (<2.0 MHz) to fast (> 2.0 MHz), the EPROM power
will turn on, and up to 20 clocks may be "skipped" to ensure that the EPROM power is
stable before reading memory.
6
0
supply voltage.
R/W
5
0
DD
R/W
Rev. 1.2
4
0
supply pin.
Function
R/W
3
0
R/W
2
0
R/W
1
0
DD
supply
MPCE
R/W
0
0