ST10R272LT6 STMicroelectronics, ST10R272LT6 Datasheet - Page 19

• Manufacturer Part Number: ST10R272LT6
• Description: IC MCU 16BIT LV ROMLESS 100-TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10R272LT6

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-TQFP, 144-VQFP
• Processor Series: ST10R2x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Interface Type: SSP, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 77
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-2045

input ports can receive 00,0000,0000h to allow direct transfers from the B-source and A-
source, respectively, to the Accumulator (case of Multiplication, Shift.). The output of the
arithmetic unit goes to the Accumulator.
It is also possible to saturate the Accumulator on a 32-bit value, automatically after every
accumulation. Automatic saturation is enabled by setting the saturation bit MS in the MCW
register. When the Accumulator is in the saturation mode and an 32-bit overflow occurs, the
accumulator is loaded with either the most positive or the most negative value representable
in a 32-bit value, depending on the direction of the overflow. The value of the Accumulator
upon saturation is 00,7fff,ffffh (positive) or ff,8000,0000h (negative) in signed arithmetic.
Automatic saturation sets the SL flag MSW. This flag is a sticky flag which means it stays set
until it is explicitly reset by the user.
40-bit overflow of the Accumulator sets the SV flag in MSW. This flag is also a sticky flag.
40-bit accumulator register
The 40-bit Accumulator consists of three SFR registers MAH, MAL and MAE. MAH and MAL
are 16-bit wide. MAE is 8-bit wide and is contained within the least significant byte of MSW.
Most co-processor operations specify the 40-bit Accumulator register as source and/or
destination operand.
Data limiter
Saturation arithmetic is also provided to selectively limit overflow, when reading the
accumulator by means of a CoSTORE <destination> MAS instruction. Limiting is performed
on the MAC Accumulator. If the contents of the Accumulator can be represented in the
destination operand size without overflow, the data limiter is disabled and the operand is not
modified. If the contents of the accumulator cannot be represented without overflow in the
destination operand size, the limiter will substitute a ‘limited’ data as explained in the following
table.
Note
Register
x
MAS
MAS
In this case, the accumulator and the status register are not affected. MAS readable
from a CoSTORE instruction.
E bit
0
1
1
Table 4 Data Limit Values
ST10R272L - MULTIPLY-ACCUMULATE UNIT (MAC)
N bit
x
0
1
Output of the Limiter
unchanged
7fffh
8000h
19/77
1