EP9307-IRZ Cirrus Logic Inc, EP9307-IRZ Datasheet - Page 5

• Manufacturer Part Number: EP9307-IRZ
• Description: IC ARM9 SOC ARM920T 272TFBGA
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9307-IRZ

• Core Size: 16/32-Bit
• Core Processor: ARM9
• Speed: 200MHz
• Connectivity: EBI/EMI, Ethernet, I²C, IrDA, Keypad/Touchscreen, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 14
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 272-TFBGA
• Controller Family/series: (ARM9)
• No. Of I/o's: 14
• Ram Memory Size: 32MB
• Cpu Speed: 200MHz
• No. Of Timers: 3
• No. Of Pwm Channels: 1
• Digital Ic Case Style: TFBGA
• Embedded Interface Type: AC97, I2S, SPI, UART, USB
• Rohs Compliant: Yes
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9307A-Z
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1133 - KIT DEVELOPMENT EP9307 ARM9
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 598-1256

USB
ExtensionID Register
Reset
Boot Configuration
ER667E2B
Description 1
USB clock divider logic operates at a maximum rate of 288MHz under worst case conditions.
Workaround
When using USB, make sure the clock frequency supplied to the USB clock divider does not exceed
288MHz. The clock supplied to the USB clock divider is sourced by PLL2. The USB clock divider is
controlled by the USBDIV setting in the CLKSET2 register. For example, configure PLL2 to output 192MHz
and USBDIV to divide by four. Ensure that the new PLL2 setting does not adversely affect any other block
using PLL2 as its clock source.
Description
The PartID field in register 0x8083_2714, ExtensionID, is not programmed.
Workaround
None, this register has been de-featured from the chip.
Description
The processor may boot into an invalid state upon initial power up of the device. When this condition occurs,
the processor will not complete its boot sequence and requires an additional power on reset (POR) to be
applied.
Workaround
Implement the recommended external reset circuit described in AN258, “EP93xx Power-up and Reset
Lockup Workaround,” which can be found at http://www.cirrus.com/en/pubs/appNote/AN258REV2.pdf.
Description
The processor may incorrectly latch the state of the CSn[7:6, 3:0] lines. The only problematic effect of this
condition is that the device may attempt to perform a 32-bit boot when it is actually configured for 16-bit boot
mode.
Workaround
Implement the recommendations described in AN273, item 7, “EP93xx Silicon Rev E Design Guidelines,”
which can be found at http://www.cirrus.com/en/pubs/appNote/AN273REV4.pdf.
NOTE: PLL2 is completely functional. This is only an issue with the USB clock divider logic.
5