LPC2103FHN48H/6,51 NXP Semiconductors, LPC2103FHN48H/6,51 Datasheet - Page 18

• Manufacturer Part Number: LPC2103FHN48H/6,51
• Description: IC ARM7 MCU FLASH 32K 48HVQFN
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2103FHN48H/6,51

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 70MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC21
• Core: ARM7 TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 70 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, DB-LQFP48-LPC2103, MCB2103, MCB2103U, MCB2103UME, KSK-LPC2103-01, KSK-LPC2103-01PL, KSK-LPC2103-02
• Development Tools By Supplier: OM10079, OM10081, OM10090
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935288984518

NXP Semiconductors
LPC2101_02_03_4
Product data sheet
6.17.3 Reset and wake-up timer
Reset has two sources on the LPC2101/02/03: the RST pin and watchdog reset. The RST
pin is a Schmitt trigger input pin with an additional glitch filter. Assertion of chip reset by
any source starts the wake-up timer (see wake-up timer description below), causing the
internal chip reset to remain asserted until the external reset is de-asserted, the oscillator
is running, a fixed number of clocks have passed, and the on-chip flash controller has
completed its initialization.
When the internal reset is removed, the processor begins executing at address 0, which is
the reset vector. At that point, all of the processor and peripheral registers have been
initialized to predetermined reset values.
The wake-up timer ensures that the oscillator and other analog functions required for chip
operation are fully functional before the processor is allowed to execute instructions. This
is important at power on, all types of reset, and whenever any of the aforementioned
functions are turned off for any reason. Since the oscillator and other functions are turned
off during Power-down and Deep power-down mode, any wake-up of the processor from
the Power-down modes makes use of the wake-up timer.
The wake-up timer monitors the crystal oscillator as the means of checking whether it is
safe to begin code execution. When power is applied to the chip, or some event caused
the chip to exit Power-down mode, some time is required for the oscillator to produce a
signal of sufficient amplitude to drive the clock logic. The amount of time depends on
many factors, including the rate of V
and its electrical characteristics (if a quartz crystal is used), as well as any other external
circuitry (e.g., capacitors), and the characteristics of the oscillator itself under the existing
ambient conditions.
Rev. 04 — 2 June 2009
DD
ramp (in the case of power on), the type of crystal
Single-chip 16-bit/32-bit microcontrollers
LPC2101/02/03
© NXP B.V. 2009. All rights reserved.
18 of 37