ATMEGA1280V-8CUR Atmel, ATMEGA1280V-8CUR Datasheet - Page 144
![MCU AVR 128K FLASH 8MHZ 100CBGA](/photos/6/89/68968/313-100-cbga_sml.jpg)
ATMEGA1280V-8CUR
Manufacturer Part Number
ATMEGA1280V-8CUR
Description
MCU AVR 128K FLASH 8MHZ 100CBGA
Manufacturer
Atmel
Series
AVR® ATmegar
Specifications of ATMEGA1280V-8CUR
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
EBI/EMI, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
86
Program Memory Size
128KB (64K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
100-TFBGA
Data Bus Width
8 bit
Data Ram Size
8 KB
Mounting Style
SMD/SMT
For Use With
ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFPATSTK503 - STARTER KIT AVR EXP MODULE 100P
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 144 of 444
- Download datasheet (10Mb)
16.6.1
16.6.2
16.6.3
2549M–AVR–09/10
Input Capture Trigger Source
Noise Canceler
Using the Input Capture Unit
The ICRn Register can only be written when using a Waveform Generation mode that utilizes
the ICRn Register for defining the counter’s TOP value. In these cases the Waveform Genera-
tion mode (WGMn3:0) bits must be set before the TOP value can be written to the ICRn
Register. When writing the ICRn Register the high byte must be written to the ICRnH I/O location
before the low byte is written to ICRnL.
For more information on how to access the 16-bit registers refer to
on page
The main trigger source for the input capture unit is the Input Capture Pin (ICPn).
Timer/Counter1 can alternatively use the analog comparator output as trigger source for the
input capture unit. The Analog Comparator is selected as trigger source by setting the analog
Comparator Input Capture (ACIC) bit in the Analog Comparator Control and Status Register
(ACSR). Be aware that changing trigger source can trigger a capture. The input capture flag
must therefore be cleared after the change.
Both the Input Capture Pin (ICPn) and the Analog Comparator output (ACO) inputs are sampled
using the same technique as for the Tn pin
identical. However, when the noise canceler is enabled, additional logic is inserted before the
edge detector, which increases the delay by four system clock cycles. Note that the input of the
noise canceler and edge detector is always enabled unless the Timer/Counter is set in a Wave-
form Generation mode that uses ICRn to define TOP.
An input capture can be triggered by software by controlling the port of the ICPn pin.
The noise canceler improves noise immunity by using a simple digital filtering scheme. The
noise canceler input is monitored over four samples, and all four must be equal for changing the
output that in turn is used by the edge detector.
The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNCn) bit in
Timer/Counter Control Register B (TCCRnB). When enabled the noise canceler introduces addi-
tional four system clock cycles of delay from a change applied to the input, to the update of the
ICRn Register. The noise canceler uses the system clock and is therefore not affected by the
prescaler.
The main challenge when using the Input Capture unit is to assign enough processor capacity
for handling the incoming events. The time between two events is critical. If the processor has
not read the captured value in the ICRn Register before the next event occurs, the ICRn will be
overwritten with a new value. In this case the result of the capture will be incorrect.
When using the Input Capture interrupt, the ICRn Register should be read as early in the inter-
rupt handler routine as possible. Even though the Input Capture interrupt has relatively high
priority, the maximum interrupt response time is dependent on the maximum number of clock
cycles it takes to handle any of the other interrupt requests.
Using the Input Capture unit in any mode of operation when the TOP value (resolution) is
actively changed during operation, is not recommended.
Measurement of an external signal’s duty cycle requires that the trigger edge is changed after
each capture. Changing the edge sensing must be done as early as possible after the ICRn
138.
ATmega640/1280/1281/2560/2561
(Figure 17-1 on page
169). The edge detector is also
“Accessing 16-bit Registers”
144
Related parts for ATMEGA1280V-8CUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATmega1280](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATMEGA1280-16CU](/photos/6/89/68968/313-100-cbga_tmb.jpg)
Part Number:
Description:
IC MCU AVR 128K FLASH 100-CBGA
Manufacturer:
Atmel
Datasheet:
![ATMEGA1280-16AU](/photos/6/70/67048/313-100-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 128K FLASH 100-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA1280-16AUR](/photos/6/70/67048/313-100-tqfp_tmb.jpg)
Part Number:
Description:
MCU AVR 128K FLASH 16MHZ 100TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA1280-16CUR](/photos/6/89/68968/313-100-cbga_tmb.jpg)
Part Number:
Description:
MCU AVR 128K FLASH 16MHZ 100CBGA
Manufacturer:
Atmel
Datasheet:
![ATMEGA128](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA128-8AC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
![ATMEGA128-16AU](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 128K 16MHZ 5V 64TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA128-16MU](/photos/12/13/121326/313-64-qfn_tmb.jpg)
Part Number:
Description:
IC AVR MCU 128K 16MHZ 5V 64-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA128-16MC](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 128K 16MHZ COM 64-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA128-16AC](/photos/12/13/121332/313-64-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 128K 16MHZ 64-TQFP
Manufacturer:
Atmel
Datasheet: