AT89C51CC01UA-RLTUM Atmel, AT89C51CC01UA-RLTUM Datasheet - Page 73

• Manufacturer Part Number: AT89C51CC01UA-RLTUM
• Description: IC 8051 MCU FLASH 32K 44-VQFP
• Manufacturer: Atmel
• Series: AT89C CANr

Specifications of AT89C51CC01UA-RLTUM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1280 B
• Interface Type: UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 2
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: CANADAPT28
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 44VQFP
• Device Core: 8051
• Family Name: AT89
• Maximum Speed: 40 MHz
• Cpu Family: AT89
• Device Core Size: 8b
• Frequency (max): 40MHz
• Total Internal Ram Size: 1.25KB
• # I/os (max): 34
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: VQFP
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AT89C51CC01UARLTUM

Watchdog Timer During
Power-down Mode and
Idle
Register
4129N–CAN–03/08
In Power-down mode the oscillator stops, which means the WDT also stops. While in
Power-down mode, the user does not need to service the WDT. There are 2 methods of
exiting Power-down mode: by a hardware reset or via a level activated external interrupt
which is enabled prior to entering Power-down mode. When Power-down is exited with
hardware reset, the Watchdog is disabled. Exiting Power-down with an interrupt is sig-
nificantly different. The interrupt shall be held low long enough for the oscillator to
stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent the
WDT from resetting the device while the interrupt pin is held low, the WDT is not started
until the interrupt is pulled high. It is suggested that the WDT be reset during the inter-
rupt service for the interrupt used to exit Power-down.
To ensure that the WDT does not overflow within a few states of exiting powerdown, it is
best to reset the WDT just before entering powerdown.
In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting
T89C51CC01 while in Idle mode, the user should always set up a timer that will periodi-
cally exit Idle, service the WDT, and re-enter Idle mode.
Table 54. WDTPRG Register
WDTPRG (S:A7h)
Watchdog Timer Duration Programming Register
Reset Value = XXXX X000b
Number
Bit
7
–
7
6
5
4
3
2
1
0
Mnemonic Description
Bit
S2
S1
S0
6
–
-
-
-
-
-
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Reserved
The value read from this bit is indeterminate. Do not set this bit.
Watchdog Timer Duration selection bit 2
Work in conjunction with bit 1 and bit 0.
Watchdog Timer Duration selection bit 1
Work in conjunction with bit 2 and bit 0.
Watchdog Timer Duration selection bit 0
Work in conjunction with bit 1 and bit 2.
5
–
4
–
3
–
S2
2
S1
1
S0
0
73