AT32UC3B0256-A2UR Atmel, AT32UC3B0256-A2UR Datasheet - Page 203

• Manufacturer Part Number: AT32UC3B0256-A2UR
• Description: MCU AVR32 256K FLASH 64-TQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B0256-A2UR

• Package / Case: 64-TQFP, 64-VQFP
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 60MHz
• Number Of I /o: 44
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Program Memory Size: 256KB (256K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Core Size: 32-Bit
• Package: 64TQFP
• Device Core: AVR32
• Family Name: AT32
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 44
• Interface Type: I2S/SPI/TWI/USART/USB
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Figure 18-8. Peripheral Deselection
18.7.3.8
32059K–03/2011
Write SPI_TDR
Write SPI_TDR
Write SPI_TDR
NPCS[0..3]
NPCS[0..3]
NPCS[0..3]
TDRE
TDRE
TDRE
Mode Fault Detection
A
A
A
to an interrupt, and thus might lead to difficulties for interfacing with some serial peripherals
requiring the chip select line to remain active during a full set of transfers.
To facilitate interfacing with such devices, the Chip Select Register can be programmed with the
CSAAT bit (Chip Select Active After Transfer) at 1. This allows the chip select lines to remain in
their current state (low = active) until transfer to another peripheral is required.
Figure 18-8 on page 203
CSAAT bits.
A mode fault is detected when the SPI is programmed in Master Mode and a low level is driven
by an external master on the NPCS0/NSS signal. NPCS0, MOSI, MISO and SPCK must be con-
figured in open drain through the GPIO controller, so that external pull up resistors are needed to
guarantee high level.
When a mode fault is detected, the MODF bit in the SR is set until the SR is read and the SPI is
automatically disabled until re-enabled by writing the SPIEN bit in the CR (Control Register) at 1.
By default, the Mode Fault detection circuitry is enabled. The user can disable Mode Fault
detection by setting the MODFDIS bit in the SPI Mode Register (MR).
DLYBCT
DLYBCT
DLYBCT
CSAAT = 0
DLYBCS
DLYBCS
DLYBCS
PCS = B
PCS=A
PCS = A
A
B
shows different peripheral deselection cases and the effect of the
A
A
A
A
DLYBCT
DLYBCT
DLYBCT
CSAAT = 1
DLYBCS
DLYBCS
PCS = B
PCS = A
A
A
PCS = A
DLYBCS
AT32UC3B
A
A
B
203