PIC24FJ256GA106T-I/PT Microchip Technology, PIC24FJ256GA106T-I/PT Datasheet - Page 40

• Manufacturer Part Number: PIC24FJ256GA106T-I/PT
• Description: IC PIC MCU FLASH 256K 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256GA106T-I/PT

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 256KB (85.5K x 24)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• A/d Bit Size: 10 bit
• A/d Channels Available: 16
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2 V
• Width: 10 mm
• For Use With: MA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCUAC164327 - MODULE SKT FOR 64TQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC24FJ256GA106T-I/PTTR

PIC24FJXXXDA1/DA2/GB2/GA3
4.6.2
Configuration bits may be programmed a single word at
a time using the PROGW command. This command
specifies the configuration data and Configuration
register
programmed, any unimplemented or reserved bits
must be programmed with a ‘1’.
Four PROGW commands are required to program the
Configuration bits. See
Configuration bit programming.
FIGURE 4-5:
DS39970B-page 40
Note:
Note 1: Refer to
address.
PROGRAMMING METHODOLOGY
If the General Segment Code-Protect bit
(GCP) is programmed to ‘0’, code memory
is code-protected and cannot be read. Code
memory must be verified before enabling
read
“Code-Protect Configuration Bits”
more information about code-protect
Configuration bits.
protection.
When
ConfigAddress + 2
ConfigAddress =
CONFIGURATION BIT PROGRAMMING FLOW
Table 2-2
Figure 4-5
Configuration
for Flash Configuration Word addresses.
See
for a flowchart for
Section 4.6.4
bits
No
for
are
PROGP response
Send PROGW
ConfigAddress
0XXXFEh?
Command
PASS?
Start
4.6.3
After the Configuration bits are programmed, the
contents of memory should be verified to ensure that
the programming was successful. Verification requires
the Configuration bits to be read back and compared
with the copy held in the programmer’s buffer. The
READP command reads back the programmed
Configuration bits and verifies that the programming
was successful.
End
Is
Is
Yes
Yes
(1)
ConfigAddress = 0XXXF8h
PROGRAMMING VERIFICATION
No
Report Error
 2010 Microchip Technology Inc.
Failure
(1)