AT32UC3L064-AUT Atmel, AT32UC3L064-AUT Datasheet - Page 103
![MCU AVR32 64KB FLASH 48TQFP](/photos/6/82/68248/313-48-vqfp_sml.jpg)
AT32UC3L064-AUT
Manufacturer Part Number
AT32UC3L064-AUT
Description
MCU AVR32 64KB FLASH 48TQFP
Manufacturer
Atmel
Series
AVR®32 UC3r
Datasheets
1.ATAVRONE-PROBECBL.pdf
(16 pages)
2.AT32UC3L-EK.pdf
(858 pages)
3.AT32UC3L016-D3HT.pdf
(110 pages)
Specifications of AT32UC3L064-AUT
Core Processor
AVR
Core Size
32-Bit
Speed
50MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, PWM, WDT
Number Of I /o
36
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.62 V ~ 3.6 V
Data Converters
A/D 9x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP, 48-VQFP
Processor Series
AT32UC3x
Core
AVR32
Data Bus Width
32 bit
Data Ram Size
16 KB
Interface Type
SPI/TWI/USART
Maximum Clock Frequency
50 MHz
Number Of Programmable I/os
36
Number Of Timers
7
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR32, EWAVR32-BL
Development Tools By Supplier
AT32UC3L-EK
Minimum Operating Temperature
- 40 C
On-chip Adc
9-ch x 10-bit
Package
48TQFP
Device Core
AVR32
Family Name
AT32
Maximum Speed
50 MHz
Operating Supply Voltage
1.8|3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3L064-AUT
Manufacturer:
HONGFA
Quantity:
30 000
Part Number:
AT32UC3L064-AUT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
10.4.22
10.4.23
32099F–11/2010
Chip
I/O Pins
6. The aWire debug interface is reset after leaving Shutdown mode
1. Power consumption in static mode is too high
2. Shutdown mode is not functional
3. VDDIN current consumption increase above 1.8V
4. Increased Power Consumption in VDDIO in sleep modes
1. PB10 is not 3.3V tolerant
2. Analog multiplexing consumes extra power
3. PA02, PB01, PB04, PB05, and RESET_N have half of the pull-up strength
4. OCD MCKO and MDO[3] are swapped in the AUX1 mapping
If the aWire debug mode is used as debug interface and the program enters Shutdown
mode, the aWire interface will be reset when the device receives a wakeup either from the
WAKE_N pin or the AST.
Fix/Workaround
None.
Power consumption in static mode is too high when PA21 is high.
Fix/Workaround
Ensure PA21 is low.
Do not enter Shutdown mode.
Fix/Workaround
None.
When VDDIN increases above 1.8V, current on VDDIN increases with up to 40µA.
Fix/Workaround
None.
If the OSC0 is enabled in crystal mode when entering a sleep mode where the OSC0 is dis-
abled, this will lead to an increased power consumption in VDDIO.
Fix/Workaround
Solution 1: Disable the OSC0 by writing a zero to the Oscillator Enable bit in the System
Control Interface (SCIF) Oscillator Control Register (SCIF.OSC0CTRL.OSCEN) before
going to any sleep mode where the OSC0 is disabled
Solution 2: Pull down or up XIN0 and XOUT0 with 1Mohm resistor.
PB10 should be grounded on the PCB and left unused.
Fix/Workaround
None.
Current consumption on VDDIO increases when the voltage on analog inputs is close to
VDDIO/2.
Fix/Workaround
None.
Pins PA02, PB01, PB04, PB05, and RESET_N have half of the specified pull-up strength.
Fix/Workaround
None.
When using the OCD AUX1 mapping of trace signals MDO[3] is located on pin PB05
and MCKO is located on PB01.
AT32UC3L016/32/64
103