ATMEGA8535L-8MU Atmel, ATMEGA8535L-8MU Datasheet - Page 199

• Manufacturer Part Number: ATMEGA8535L-8MU
• Description: IC AVR MCU 8K 8MHZ 3V 44-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8535L-8MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-VQFN Exposed Pad
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, TWI, UART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 44MLF EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 78. Status Codes for Slave Transmitter Mode
2502K–AVR–10/06
Status Code
(TWSR)
Prescaler Bits
are 0
0xA8
0xB0
0xB8
0xC0
0xC8
Status of the Two-wire Serial Bus
and Two-wire Serial Interface
Hardware
Own SLA+R has been received;
ACK has been returned
Arbitration lost in SLA+R/W as
Master; own SLA+R has been
received; ACK has been returned
Data byte in TWDR has been
transmitted; ACK has been
received
Data byte in TWDR has been
transmitted; NOT ACK has been
received
Last data byte in TWDR has been
transmitted (TWEA = “0”); ACK
has been received
by setting TWEA. This implies that the TWEA bit may be used to temporarily isolate the
TWI from the Two-wire Serial Bus.
In all sleep modes other than Idle mode, the clock system to the TWI is turned off. If the
TWEA bit is set, the interface can still acknowledge its own slave address or the general
call address by using the Two-wire Serial Bus clock as a clock source. The part will then
wake up from sleep and the TWI will hold the SCL clock will low during the wake up and
until the TWINT Flag is cleared (by writing it to one). Further data transmission will be
carried out as normal, with the AVR clocks running as normal. Observe that if the AVR is
set up with a long start-up time, the SCL line may be held low for a long time, blocking
other data transmissions.
Note that the Two-wire Serial Interface Data Register – TWDR – does not reflect the last
byte present on the bus when waking up from these sleep modes.
To/from TWDR
Load data byte or
Load data byte
Load data byte or
Load data byte
Load data byte or
Load data byte
No TWDR action or
No TWDR action or
No TWDR action or
No TWDR action
No TWDR action or
No TWDR action or
No TWDR action or
No TWDR action
Application Software Response
STA
X
X
X
X
X
X
0
0
1
1
0
0
1
1
STO
0
0
0
0
0
0
0
0
0
0
0
0
0
0
To TWCR
TWINT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TWEA
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Next Action Taken by TWI Hardware
Last data byte will be transmitted and NOT ACK should
be received
Data byte will be transmitted and ACK should be re-
ceived
Last data byte will be transmitted and NOT ACK should
be received
Data byte will be transmitted and ACK should be re-
ceived
Last data byte will be transmitted and NOT ACK should
be received
Data byte will be transmitted and ACK should be re-
ceived
Switched to the not addressed Slave mode;
no recognition of own SLA or GCA
Switched to the not addressed Slave mode;
own SLA will be recognized;
GCA will be recognized if TWGCE = “1”
Switched to the not addressed Slave mode;
no recognition of own SLA or GCA;
a START condition will be transmitted when the bus
becomes free
Switched to the not addressed Slave mode;
own SLA will be recognized;
GCA will be recognized if TWGCE = “1”;
a START condition will be transmitted when the bus
becomes free
Switched to the not addressed Slave mode;
no recognition of own SLA or GCA
Switched to the not addressed Slave mode;
own SLA will be recognized;
GCA will be recognized if TWGCE = “1”
Switched to the not addressed Slave mode;
no recognition of own SLA or GCA;
a START condition will be transmitted when the bus
becomes free
Switched to the not addressed Slave mode;
own SLA will be recognized;
GCA will be recognized if TWGCE = “1”;
a START condition will be transmitted when the bus
becomes free
ATmega8535(L)
199