ATMEGA8515-16PU Atmel, ATMEGA8515-16PU Datasheet - Page 182

• Manufacturer Part Number: ATMEGA8515-16PU
• Description: IC AVR MCU 8K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Cpu Speed: 16 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 35
• Interface: SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 8K Bytes
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 2
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

Parallel Programming
Parameters, Pin
Mapping, and
Commands
Signal Names
182
ATmega8515(L)
This section describes how to parallel program and verify Flash Program memory,
EEPROM Data memory, Memory Lock bits, and Fuse bits in the ATmega8515. Pulses
are assumed to be at least 250 ns unless otherwise noted.
In this section, some pins of the ATmega8515 are referenced by signal names describ-
ing their functionality during parallel programming, see Figure 75 and Table 85. Pins not
described in the following table are referenced by pin names.
The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a posi-
tive pulse. The bit coding is shown in Table 87.
When pulsing WR or OE, the command loaded determines the action executed. The dif-
ferent Commands are shown in Table 88.
Figure 75. Parallel Programming
Table 85. Pin Name Mapping
Signal Name in Programming Mode
RDY/BSY
PAGEL
DATA
BS1
XA0
XA1
BS2
WR
OE
RDY/BSY
PAGEL
+12 V
BS2
BS1
XA0
XA1
WR
OE
PD1
PD2
PD3
PD4
PD5
PD6
PD7
RESET
XTAL1
GND
PA0
Pin Name
PB7-0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PA0
PB7 - PB0
VCC
I/O
I/O
O
I
I
I
I
I
I
I
XTAL Action Bit 0
XTAL Action Bit 1
Function
0: Device is busy programming, 1:
Device is ready for new command
Output Enable (Active low)
Write Pulse (Active low)
Byte Select 1 (“0” selects low
byte, “1” selects high byte)
Program memory and EEPROM
data Page Load
Byte Select 2 (“0” selects low
byte, “1” selects 2’nd high byte)
Bi-directional Data bus (Output
when OE is low)
+5V
DATA
2512K–AVR–01/10