ATMEGA8515-16AU Atmel, ATMEGA8515-16AU Datasheet - Page 37

• Manufacturer Part Number: ATMEGA8515-16AU
• Description: IC AVR MCU 8K 16MHZ 5V 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Interface Type: SPI/USART
• Total Internal Ram Size: 512Byte
• # I/os (max): 35
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 2
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Package: 44TQFP
• Family Name: ATmega
• Maximum Speed: 16 MHz
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

Low-frequency Crystal
Oscillator
2512K–AVR–01/10
Table 8. Start-up Times for the Crystal Oscillator Clock Selection (Continued)
Notes:
To use a 32.768 kHz watch crystal as the clock source for the device, the Low-fre-
quency Crystal Oscillator must be selected by setting the CKSEL Fuses to “1001”. The
crystal should be connected as shown in Figure 19. By programming the CKOPT Fuse,
the user can enable internal capacitors on XTAL1 and XTAL2, thereby removing the
need for external capacitors. The internal capacitors have a nominal value of 36 pF.
When this Oscillator is selected, start-up times are determined by the SUT Fuses as
shown in Table 9.
Table 9. Start-up Times for the Low-frequency Crystal Oscillator Clock Selection
Note:
CKSEL0
SUT1..0
00
01
10
11
1
1
1
1. These options should only be used when not operating close to the maximum fre-
2. These options are intended for use with ceramic resonators and will ensure fre-
1. These options should only be used if frequency stability at start-up is not important
quency of the device, and only if frequency stability at start-up is not important for the
application. These options are not suitable for crystals.
quency stability at start-up. They can also be used with crystals when not operating
close to the maximum frequency of the device, and if frequency stability at start-up is
not important for the application.
for the application.
SUT1..0
from Power-down
Start-up Time
01
10
11
1K CK
1K CK
32K CK
from Power-down
(1)
(1)
Start-up Time
16K CK
16K CK
16K CK
Additional Delay from
Reset (V
4.1 ms
65 ms
65 ms
Additional Delay from
CC
Reset (V
Reserved
= 5.0V)
4.1 ms
65 ms
CC
–
= 5.0V)
Recommended Usage
enabled
ATmega8515(L)
Fast rising power or BOD
Slowly rising power
Stable frequency at start-up
Recommended
Usage
Crystal Oscillator,
BOD enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator,
slowly rising power
37