ATMEGA8L-8PU Atmel, ATMEGA8L-8PU Datasheet - Page 38

• Manufacturer Part Number: ATMEGA8L-8PU
• Description: IC AVR MCU 8K 8MHZ 3V 28DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8L-8PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-DIP (0.300", 7.62mm)
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SPI/TWI/USART
• Total Internal Ram Size: 1KB
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 6-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

38
ATmega8(L)
Figure 14. Reset Logic
Table 15. Reset Characteristics
Notes:
Symbol
V
V
V
V
t
t
BOD
RST
HYST
POT
RST
BOT
1. The Power-on Reset will not work unless the supply voltage has been below V
2. V
BODLEVEL
this is the case, the device is tested down to V
antees that a Brown-out Reset will occur before V
operation of the microcontroller is no longer guaranteed. The test is performed using
BODLEVEL = 1 for ATmega8L and BODLEVEL = 0 for ATmega8. BODLEVEL = 1 is not appli-
cable for ATmega8
Parameter
Power-on Reset Threshold
Voltage (rising)
Power-on Reset Threshold
Voltage (falling)
RESET Pin Threshold Voltage
Minimum pulse width on
RESET Pin
Brown-out Reset Threshold
Voltage
Minimum low voltage period for
Brown-out Detection
Brown-out Detector hysteresis
BODEN
BOT
may be below nominal minimum operating voltage for some devices. For devices where
(2)
Pull-up Resistor
FILTER
SPIKE
(1)
CKSEL[3:0]
Reset Circuit
SUT[1:0]
Brown-Out
Watchdog
Oscillator
Generator
Clock
BODLEVEL = 1
BODLEVEL = 0
BODLEVEL = 1
BODLEVEL = 0
Condition
CK
MCU Control and Status
Register (MCUCSR)
DATA BUS
CC
Delay Counters
= V
BOT
Min
0.2
2.4
3.7
CC
during the production test. This guar-
drops to a voltage where correct
Typ
130
1.4
1.3
2.6
4.0
2
2
TIMEOUT
Max
2.3
2.3
0.9
1.5
2.9
4.5
Units
POT
V
mV
2486Z–AVR–02/11
µs
µs
V
V
CC
(falling)