AT90USB162-16AUR Atmel, AT90USB162-16AUR Datasheet - Page 187

• Manufacturer Part Number: AT90USB162-16AUR
• Description: IC AVR MCU 16K FLASH 32TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB162-16AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/USART/debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATSTK526, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• Cpu Family: AT90
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 22
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: TQFP
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: AT90USB162-16AU; AT90USB162-16AURTR; AT90USB162-16AUTR; AT90USB162-16AUTR

19.3.3
19.4
19.4.1
19.4.2
7707F–AVR–11/10
General Operating Modes
Design guidelines
Introduction
Power-on and reset
The USB controller is disabled and reset after a hardware reset generated by:
But another available and optionnal reset source is :
In this case, the USB controller is reset, but not disabled (so that the device remains attached).
The next diagram explains the USB controller main states on power-on:
Figure 19-7. USB controller states after reset
When the USB controller is in reset state:
• Serial resistors on USB Data lines must have 22 Ohms value (
• Traces from the input USB receptable (or from the cable connection in the case of a tethered
• Voltage transcient / ESD suppressors may also be used to prevent USB pads to be damaged
• U
• A 10µF capacitor is highly recommended on VBUS line
• USBE is not set
device) to the USB microcontroller pads should be as short as possibles, and follow
differential traces routing rules (same length, as near as possible, avoid vias accumulation).
by external disturbances.
cap
– Power on reset
– External reset
– Watchdog reset
– Brown out reset
– debugWIRE reset
– USB End Of Reset
capacitor should be 1µF (
Clock stopped
Dev ice
FRZCLK=1
+/-
Macro off
USBE=1
10%) for correct operation.
HW RESET from EOR
USBE=0
Reset
USBE=0
(excepted from EOR)
HW RESET
USBE=0
<any other
state>
AT90USB82/162
+/-
5%).
187