PIC16C712-20/SO Microchip Technology, PIC16C712-20/SO Datasheet - Page 77

• Manufacturer Part Number: PIC16C712-20/SO
• Description: IC MCU OTP 1KX14 A/D PWM 18SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C712-20/SO

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Core Processor: PIC
• Speed: 20MHz
• Number Of I /o: 13
• Program Memory Type: OTP
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-SOIC (7.5mm Width)
• Controller Family/series: PIC16C
• No. Of I/o's: 13
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

12.1
DC CHARACTERISTICS
D001
D001A
D002*
D003
D004*
D004A*
D005
D010
D013
D020
D021
D021B
D022*
D022A*
1A
Note1:
Param
1999 Microchip Technology Inc.
No.
2:
3:
4:
5:
6:
7:
*
†
DC Characteristics:
These parameters are characterized but not tested.
Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
This is the limit to which V
The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and
switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current con-
sumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to V
MCLR = V
The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the
part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
For RC osc mode, current through Rext is not included. The current through the resistor can be estimated by the formula Ir =
V
Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for
design guidance only. This is not tested.
The
I
This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will operate correctly to
this trip point.
V
V
V
S
V
I
I
F
DD
DD
PD
DD
Sym
I
I
OSC
DD
DR
POR
VDD
BOR
WDT
BOR
or I
/2Rext (mA) with Rext in kOhm.
current is the additional current consumed when this peripheral is enabled. This current should be added to the base
PD
Supply Voltage
RAM Data Retention Voltage
V
nal Power-on Reset signal
V
Power-on Reset signal
Brown-out Reset
voltage trip point
Supply Current
Power-down Current
Module Differential Current
Watchdog Timer
Brown-out Reset
LP Oscillator Operating Frequency
RC Oscillator Operating Frequency
XT Oscillator Operating Frequency
HS Oscillator Operating Frequency
measurement.
DD
DD
DD
; WDT enabled/disabled as specified.
Start Voltage to ensure inter-
Rise Rate to ensure internal
Characteristic
(2,5)
DD
DD
can be lowered without losing RAM data.
PIC16C712/716-04 (Commercial, Industrial, Extended)
PIC16C712/716-20 (Commercial, Industrial, Extended)
measurements in active operation mode are:
(3,5)
(6)
(1)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Preliminary
V
0.05
TBD
3.65
Min
BOR
4.0
0
0
0
0
-
-
-
-
-
-
-
-
-
-
*
Typ†
TBD
10.5
V
1.5
0.8
4.0
1.5
1.5
2.5
6.0
—
—
—
—
-
-
SS
-
-
-
Max
4.35
200
200
5.5
5.5
2.5
8.0
42
16
19
19
20
20
4
4
-
-
-
-
Units
V/ms PWRT enabled (PWRTE bit clear)
MHz
MHz
MHz
DD
KHz
mA
mA
V
V
V
V
V
-40°C
-40°C
A
A
A
A
A
A
and V
0°C
PIC16C712/716
DD
BOR enabled (Note 7)
See section on Power-on Reset for details
PWRT disabled (PWRTE bit set)
See section on Power-on Reset for details
BODEN bit set
F
F
V
V
V
V
WDTE bit set, V
BODEN bit set, V
All temperatures
All temperatures
All temperatures
All temperatures
,
OSC
OSC
DD
DD
DD
DD
SS
.
= 4.0V, WDT disabled,-40 C to +125 C
= 4.0V, WDT enabled,-40 C to +85 C
= 4.0V, WDT disabled, 0 C to +70 C
= 4.0V, WDT disabled,-40 C to +85 C
T
T
T
= 4 MHz, V
= 20 MHz, V
A
A
A
+125°C
+70°C
+85°C
Conditions
DD
DD
DD
DD
= 4.0V
= 4.0V
= 5.0V
DS41106A-page 77
= 4.0V
for commercial
for industrial
for extended