PIC16HV785-I/P Microchip Technology, PIC16HV785-I/P Datasheet - Page 33

• Manufacturer Part Number: PIC16HV785-I/P
• Description: IC PIC MCU FLASH 2KX14 20DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16HV785-I/P

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16HV
• No. Of I/o's: 18
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Processor Series: PIC16H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232, USB
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 14 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162060 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOICACICE0203 - MPLABICE 20P 300 MIL ADAPTER
• Connectivity: -
• Lead Free Status / Rohs Status: Details

FIGURE 3-7:
3.7
The Fail-Safe Clock Monitor (FSCM) is designed to
allow the device to continue to operate in the event of
an oscillator failure. The FSCM can detect oscillator
failure at any point after the device has exited a Reset
or Sleep condition and the Oscillator Start-up Timer
(OST) has expired.
FIGURE 3-8:
The FSCM function is enabled by setting the FCMEN
bit in Configuration Word (CONFIG). It is applicable to
all external clock options (LP, XT, HS, EC, RC or I/O
modes).
In the event of an external clock failure, the FSCM will
set the OSFIF bit in the PIR1 Register and generate an
oscillator fail interrupt if the OSFIE bit in the PIE1 Reg-
ister is set. The device will then switch the system clock
to the internal oscillator. The system clock will continue
to come from the internal oscillator unless the external
clock recovers and the Fail-Safe condition is exited.
© 2008 Microchip Technology Inc.
Program Counter
LFINTOSC
Oscillator
(~32 μs)
Primary
31 kHz
Clock
System Clock
Fail-Safe Clock Monitor
INTOSC
OSC1
OSC2
(~2 ms)
488 Hz
÷ 64
Q1
TWO-SPEED START-UP
FSCM BLOCK DIAGRAM
0
(edge-triggered)
Clock Monitor
Q2
Latch (CM)
C
S
1
T
T
OST
Q3
Q
Q
1022 1023
PC
Q4
Detected
Failure
Clock
Q1
Q2
The frequency of the internal oscillator will depend
upon
(OSCCON<6:4>). Upon entering the Fail-Safe condi-
tion, the OSTS bit in the OSCCON Register is automat-
ically cleared to reflect that the internal oscillator is
active and the WDT is cleared. The SCS bit in the OSC-
CON Register is not updated. Enabling FSCM does not
affect the LTS bit.
The FSCM sample clock is generated by dividing the
LFINTOSC clock by 64. This will allow enough time
between FSCM sample clocks for a system clock edge
to occur. Figure 3-8 shows the FSCM block diagram.
On the rising edge of the sample clock, the monitoring
latch (CM = 0) will be cleared. On a falling edge of the
primary system clock, the monitoring latch will be set
(CM = 1). In the event that a falling edge of the sample
clock occurs, and the monitoring latch is not set, a clock
failure has been detected. The assigned internal
oscillator is enabled when FSCM is enabled as
reflected by the IRCF bits.
Note:
the
PC + 1
PIC16F785/HV785
Two-Speed
enabled when the Fail-Safe Clock Monitor
mode is enabled.
value
Q3
contained
Start-up
Q4
in
is
DS41249E-page 31
the
PC + 2
automatically
Q1
IRCF
bits