ST72F32AK2T6 STMicroelectronics, ST72F32AK2T6 Datasheet - Page 40

• Manufacturer Part Number: ST72F32AK2T6
• Description: MCU 8BIT 8KB FLASH/ROM 32-TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F32AK2T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFP, 32-VQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7MDT20-DVP3, ST7MDT20J-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 1.4 mm
• Length: 7 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 3.8 V
• Width: 7 mm
• For Use With: 497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5610

ST7232A
POWER SAVING MODES (Cont’d)
8.4.2 HALT MODE
The HALT mode is the lowest power consumption
mode of the MCU. It is entered by executing the
‘HALT’ instruction when the OIE bit of the Main
Clock Controller Status register (MCCSR) is
cleared (see
tails on the MCCSR register).
The MCU can exit HALT mode on reception of ei-
ther a specific interrupt (see
Mapping,” on page
HALT mode by means of a RESET or an interrupt,
the oscillator is immediately turned on and the 256
or 4096 CPU cycle delay is used to stabilize the
oscillator. After the start up delay, the CPU
resumes operation by servicing the interrupt or by
fetching the reset vector which woke it up (see
ure
When entering HALT mode, the I[1:0] bits in the
CC register are forced to ‘10b’to enable interrupts.
Therefore, if an interrupt is pending, the MCU
wakes up immediately.
In HALT mode, the main oscillator is turned off
causing all internal processing to be stopped, in-
cluding the operation of the on-chip peripherals.
All peripherals are not clocked except the ones
which get their clock supply from another clock
generator (such as an external or auxiliary oscilla-
tor).
The compatibility of Watchdog operation with
HALT mode is configured by the “WDGHALT” op-
tion bit of the option byte. The HALT instruction
when executed while the Watchdog system is en-
abled, can generate a Watchdog RESET (see
Section 14.1 on page
Figure 25. HALT Timing Overview
40/157
1
[MCCSR.OIE=0]
INSTRUCTION
RUN
26).
HALT
HALT
Section 10.2 on page 53
256 OR 4096 CPU
33) or a RESET. When exiting
CYCLE DELAY
INTERRUPT
145) for more details.
RESET
OR
Table 8, “Interrupt
VECTOR
FETCH
for more de-
RUN
Fig-
Figure 26. HALT Mode Flow-chart
Notes:
1. WDGHALT is an option bit. See option byte sec-
tion for more details.
2. Peripheral clocked with an external clock source
can still be active.
3. Only some specific interrupts can exit the MCU
from HALT mode (such as external interrupt). Re-
fer to
more details.
4. Before servicing an interrupt, the CC register is
pushed on the stack. The I[1:0] bits of the CC reg-
ister are set to the current software priority level of
the interrupt routine and recovered when the CC
register is popped.
N
HALT INSTRUCTION
WATCHDOG
WDGHALT
Table 8, “Interrupt Mapping,” on page 33
(MCCSR.OIE=0)
RESET
1
INTERRUPT
Y
1)
3)
ENABLE
256 OR 4096 CPU CLOCK
OR SERVICE INTERRUPT
0
FETCH RESET VECTOR
OSCILLATOR
PERIPHERALS
CPU
I[1:0] BITS
OSCILLATOR
PERIPHERALS
CPU
I[1:0] BITS
OSCILLATOR
PERIPHERALS
CPU
I[1:0] BITS
N
CYCLE
RESET
Y
WATCHDOG
DELAY
DISABLE
2)
XX
XX
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
10
4)
4)
for