C8051F040-GQ Silicon Laboratories Inc, C8051F040-GQ Datasheet - Page 229

• Manufacturer Part Number: C8051F040-GQ
• Description: IC 8051 MCU 64K FLASH 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F04xr

Specifications of C8051F040-GQ

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 100-TQFP, 100-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b, 13x12b; D/A 2x10b, 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: CAN/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F040DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 8-bit or 13-ch x 12-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 64
• Ram Memory Size: 4352Byte
• Cpu Speed: 25MHz
• No. Of Timers: 5
• Rohs Compliant: Yes
• Data Rom Size: 64 KB
• A/d Bit Size: 12 bit
• A/d Channels Available: 13
• Height: 1 mm
• Length: 14 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 14 mm
• Package: 100TQFP
• Device Core: 8051
• Family Name: C8051F04x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1205 - DEV KIT FOR F040/F041/F042/F043
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1204

18.1.1. CAN Controller Timing
The CAN controller’s system clock (f
external oscillator (such as a quartz crystal) is typically required due to the high accuracy requirements for
CAN communication. Refer to Section “4.10.4 Oscillator Tolerance Range” in the Bosch CAN User’s Guide
for further information regarding this topic.
18.1.2. Example Timing Calculation for 1 Mbit/Sec Communication
This example shows how to configure the CAN contoller timing parameters for a 1 Mbit/Sec bit rate.
Table 18.1 shows timing-related system parameters needed for the calculation.
Each bit transmitted on a CAN network has 4 segments (Sync_Seg, Prop_Seg, Phase_Seg1, and
Phase_Seg2), as shown in Figure 18.3. The sum of these segments determines the CAN bit time (1/bit
rate). In this example, the desired bit rate is 1 Mbit/sec; therefore, the desired bit time is 1000 ns.
Notes:
CIP-51 system clock (SYSCLK)
CAN Controller system clock
1. The CAN time quantum (t
2. The Baud Rate Prescaler (BRP) is defined as the value of the BRP Extension Register plus 1. The BRP
3. Based on an ISO-11898 compliant transceiver. CAN does not specify a physical layer.
Propagation delay time
CAN clock period (t
CAN time quantum (t
are often specified in integer multiples of the time quantum.
Extension Register has a reset value of 0x0000; the Baud Rate Prescaler has a reset value of 1.
CAN bus length
Parameter
(f
sys
1t
)
q
Figure 18.3. Four Segments of a CAN Bit Time
Sync_Seg
Table 18.1. Background System Information
sys
q
1t
)
)
3
Prop_Seg
1 to 8 t
q
q
) is the smallest unit of time recognized by the CAN contoller. Bit timing parameters
sys
q
CAN Bit Time (4 to 25 t
22.1184 MHz
22.1184 MHz
) is derived from the CIP-51 system clock (SYSCLK). Note that an
45.211 ns
45.211 ns
400 ns
Value
10 m
Rev. 1.5
Phase_Seg1
1 to 8 t
22.1184 MHz quartz crystal is connected between
C8051F040/1/2/3/4/5/6/7
External oscillator in ‘Crystal Oscillator Mode’. A
2 x (transceiver loop delay + bus line delay)
5 ns/m signal delay between CAN nodes.
q
q
)
Derived from t
Derived from SYSCLK.
Phase_Seg2
Derived from 1/f
XTAL1 and XTAL2.
Sample Point
Description
1 to 8 t
sys
q
x BRP
sys
.
1,2
229