C8051F040-GQ Silicon Laboratories Inc, C8051F040-GQ Datasheet - Page 208
![IC 8051 MCU 64K FLASH 100TQFP](/photos/12/20/122007/c8051f040-gq_sml.jpg)
C8051F040-GQ
Manufacturer Part Number
C8051F040-GQ
Description
IC 8051 MCU 64K FLASH 100TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F04xr
Datasheets
1.C8051F040-TB.pdf
(328 pages)
2.C8051F040-TB.pdf
(2 pages)
3.C8051F043-GQ.pdf
(328 pages)
Specifications of C8051F040-GQ
Program Memory Type
FLASH
Program Memory Size
64KB (64K x 8)
Package / Case
100-TQFP, 100-VQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
CAN, EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
64
Ram Size
4.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 8x8b, 13x12b; D/A 2x10b, 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F0x
Core
8051
Data Bus Width
8 bit
Data Ram Size
4.25 KB
Interface Type
CAN/SMBus/SPI/UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
64
Number Of Timers
5
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F040DK
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 8-bit or 13-ch x 12-bit
On-chip Dac
2-ch x 12-bit
No. Of I/o's
64
Ram Memory Size
4352Byte
Cpu Speed
25MHz
No. Of Timers
5
Rohs Compliant
Yes
Data Rom Size
64 KB
A/d Bit Size
12 bit
A/d Channels Available
13
Height
1 mm
Length
14 mm
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.7 V
Width
14 mm
Package
100TQFP
Device Core
8051
Family Name
C8051F04x
Maximum Speed
25 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1205 - DEV KIT FOR F040/F041/F042/F043
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1204
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F040-GQ
Manufacturer:
SiliconL
Quantity:
702
Company:
Part Number:
C8051F040-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F040-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Part Number:
C8051F040-GQR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
C8051F040/1/2/3/4/5/6/7
All Port pins on Ports 0 through 3 that are not allocated by the Crossbar can be accessed as General-Pur-
pose I/O (GPIO) pins by reading and writing the associated Port Data registers (See SFR Definition 17.5,
SFR Definition 17.7, SFR Definition 17.10, and SFR Definition 17.13), a set of SFR’s which are both byte-
and bit-addressable. The output states of Port pins that are allocated by the Crossbar are controlled by the
digital peripheral that is mapped to those pins. Writes to the Port Data registers (or associated Port bits)
will have no effect on the states of these pins.
A Read of a Port Data register (or Port bit) will always return the logic state present at the pin itself, regard-
less of whether the Crossbar has allocated the pin for peripheral use or not. An exception to this occurs
during the execution of a read-modify-write instruction (ANL, ORL, XRL, CPL, INC, DEC, DJNZ, JBC,
CLR, SET, and the bitwise MOV operation). During the read cycle of the read-modify-write instruction, it is
the contents of the Port Data register, not the state of the Port pins themselves, which is read.
Because the Crossbar registers affect the pinout of the peripherals of the device, they are typically config-
ured in the initialization code of the system before the peripherals themselves are configured. Once config-
ured, the Crossbar registers are typically left alone.
Once the Crossbar registers have been properly configured, the Crossbar is enabled by setting XBARE
(XBR2.4) to a logic 1. Until XBARE is set to a logic 1, the output drivers on Ports 0 through 3 are
explicitly disabled in order to prevent possible contention on the Port pins while the Crossbar reg-
isters and other registers which can affect the device pinout are being written.
The output drivers on Crossbar-assigned input signals (like RX0, for example) are explicitly disabled; thus
the values of the Port Data registers and the PnMDOUT registers have no effect on the states of these
pins.
17.1.2. Configuring the Output Modes of the Port Pins
The output drivers on Ports 0 through 3 remain disabled until the Crossbar is enabled by setting XBARE
(XBR2.4) to a logic 1.
The output mode of each port pin can be configured to be either Open-Drain or Push-Pull. In the Push-Pull
configuration, writing a logic 0 to the associated bit in the Port Data register will cause the Port pin to be
driven to GND, and writing a logic 1 will cause the Port pin to be driven to V
. In the Open-Drain configu-
DD
ration, writing a logic 0 to the associated bit in the Port Data register will cause the Port pin to be driven to
GND, and a logic 1 will cause the Port pin to assume a high-impedance state. The Open-Drain configura-
tion is useful to prevent contention between devices in systems where the Port pin participates in a shared
interconnection in which multiple outputs are connected to the same physical wire (like the SDA signal on
an SMBus connection).
The output modes of the Port pins on Ports 0 through 3 are determined by the bits in the associated PnM-
DOUT registers (See SFR Definition 17.6, SFR Definition 17.9, SFR Definition 17.12, and SFR Definition
17.15). For example, a logic 1 in P3MDOUT.7 will configure the output mode of P3.7 to Push-Pull; a logic 0
in P3MDOUT.7 will configure the output mode of P3.7 to Open-Drain. All Port pins default to Open-Drain
output.
The PnMDOUT registers control the output modes of the port pins regardless of whether the Crossbar has
allocated the Port pin for a digital peripheral or not. The exceptions to this rule are: the Port pins connected
to SDA, SCL, RX0 (if UART0 is in Mode 0), and RX1 (if UART1 is in Mode 0) are always configured as
Open-Drain outputs, regardless of the settings of the associated bits in the PnMDOUT registers.
208
Rev. 1.4