MC9S08GT16AMFDE Freescale Semiconductor, MC9S08GT16AMFDE Datasheet - Page 276

• Manufacturer Part Number: MC9S08GT16AMFDE
• Description: IC MCU 16K FLASH 2K RAM 48-QFN
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT16AMFDE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 39
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-QFN
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, IRSCI, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 39
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 48QFN EP
• Family Name: HCS08
• Maximum Speed: 40 MHz
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical Characteristics
A.10
This section describes ac timing characteristics for each peripheral system. For detailed information about
how clocks for the bus are generated, see
276
1
2
3
4
5
6
7
8
Self-clocked mode frequency is the frequency that the DCO generates when the FLL is open-loop.
Loss of reference frequency is the reference frequency detected internally, which transitions the ICG into self-clocked
mode if it is not in the desired range.
Loss of DCO frequency is the DCO frequency detected internally, which transitions the ICG into FLL bypassed external
mode (if an external reference exists) if it is not in the desired range.
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period of time required for the FLL to lock after entering FLL engaged internal or external
modes. If a crystal/resonator is being used as the reference, this specification assumes it is already running.
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the FLL circuitry via V
percentage for a given interval.
See
Figure A-10
AC Characteristics
–60
Figure A-10. Internal Oscillator Deviation from Trimmed Frequency
–40
DDA
–20
MC9S08GT16A/GT8A Data Sheet, Rev. 1
and V
TEMPERATURE (°C)
–0.1
0.1
SSA
0
Chapter 9, “Internal Clock Generator
and variation in crystal oscillator frequency increase the C
–0.2
–0.3
–0.4
–0.5
–0.6
20
40
60
80
(S08ICGV4).”
2 V
3 V
Freescale Semiconductor
100
Jitter
120
ICGOUT
.