C8051F230-GQ Silicon Laboratories Inc, C8051F230-GQ Datasheet - Page 84

• Manufacturer Part Number: C8051F230-GQ
• Description: IC 8051 MCU 8K FLASH 48TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F2xxr

Specifications of C8051F230-GQ

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 48-TQFP, 48-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 32
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F2x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F226DK
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 32
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 48TQFP
• Device Core: 8051
• Family Name: C8051F2xx
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1242

C8051F2xx
down all digital peripherals. Each analog peripheral must be shut down individually prior to entering Stop
Mode. Stop mode can only be terminated by an internal or external reset. On reset, the CIP-51 performs
the normal reset sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to sleep for longer than the MCD
timeout of 100  sec.
84
Bit7:
Bits6–2: GF4–GF0: General Purpose Flags 4–0.
Bit1:
Bit0:
SMOD
R/W
Bit7
SMOD: Serial Port Baud Rate Doubler Enable.
0: Serial Port baud rate is that defined by Serial Port Mode in SCON.
1: Serial Port baud rate is double that defined by Serial Port Mode in SCON.
These are general purpose flags for use under software control.
STOP: Stop Mode Select.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: Goes into power down mode. (Turns off internal oscillator).
IDLE: Idle Mode Select.
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: Goes into idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial
Ports, and Analog Peripherals are still active.)
GF4
R/W
Bit6
SFR Definition 9.14. PCON: Power Control Register
GF3
R/W
Bit5
GF2
R/W
Bit4
Rev. 1.6
GF1
R/W
Bit3
GF0
R/W
Bit2
STOP
R/W
Bit1
IDLE
R/W
Bit0
SFR Address:
Reset Value
00000000
0x87